91347-2 Tyco Electronics, 91347-2 Datasheet

no-image

91347-2

Manufacturer Part Number
91347-2
Description
SEATING TL 4 PR 15 COL HDR
Manufacturer
Tyco Electronics
Datasheet
1.91347-1.pdf (4 pages)

Specifications of 91347-2

Lead Free Status / RoHS Status
Not applicable / Not applicable
1. INTRODUCTION
This instruction sheet covers the use and
maintenance of Seating Tools 91347–[ ], 91350–[ ],
and 91376–1 which are used to seat Hard Metric Zd
(HM–Zd) Type connectors with Eye of Needle Type
contacts. See Figure 1. Tools 91347–[ ] are used to
seat four–pair HM–Zd Receptacle Connectors; tool
91350–1 is used to seat two–pair HM–Zd Receptacle
Connectors; and tool 91376–1 is used to seat
three–pair HM–Zd Receptacle Connectors. These
tools allow solderless printed circuit (pc) board
installation.
Read these instructions and understand them before
using the seating tools and support anvil.
E
All International Rights Reserved
AMP and Tyco are trademarks. *Trademark
Other products, logos, and company names used are the property of their respective owners.
NOTE: A printed circuit board
support fixture is needed for
use with the seating tool. You
can design a pc board support
fixture for your specific needs.
2004 Tyco Electronics Corporation, Harrisburg, PA
NOTE
All dimensions on this document are in metric
units [with U.S. customary units in brackets].
Figures and illustrations are for reference only,
and are not drawn to scale.
Eye of Needle Type
Contact Board Retention
Feature
This controlled document is subject to change.
For latest revision, call the FAX/PRODUCT INFO number.
Seating Tools 91347–[ ],
91350–[ ], and 91376–1 for
HM–Zd Receptacle Connectors
Figure 1
Reasons for reissue of this sheet are provided in
Section 8, REVISION SUMMARY.
2. DESCRIPTION
The seating tool is a one–piece design. During
seating, the seating tool covers the connector and
presses on the top surface of the connector when the
applicator ram applies force to the seating tool. The
support anvil is positioned into a pc board support
fixture to support the pc board.
3. REQUIREMENTS
3.1. PC Board Support Fixture (Customer Supplied)
A pc board support must be used to provide proper
support for the pc board and alignment of the tool to
the receptacle pins, and to protect the pc board and
connector contacts from damage. This pc board
support is needed for use with this seating tool and
TOOLING ASSISTANCE CENTER 1–800–722–1111
FAX/PRODUCT INFO 1–800–522–6752
For Regional Customer Service, visit our website at
www.tycoelectronics.com
Typical HM–Zd Two–Pair
Receptacle Connector
Assembly (Ref)
Seating Tool
91350–1
(Shown)
PC Support
(Customer Supplied)
Printed Circuit
Board
(Ref)
Instruction Sheet
408–8500
11 FEB 04 Rev C
1 of 4
LOC B

91347-2 Summary of contents

Page 1

... Seating Tools 91347–[ ], 91350–[ ], and 91376–1 which are used to seat Hard Metric Zd (HM–Zd) Type connectors with Eye of Needle Type contacts. See Figure 1. Tools 91347–[ ] are used to seat four–pair HM–Zd Receptacle Connectors; tool 91350–1 is used to seat two–pair HM–Zd Receptacle Connectors ...

Page 2

... Applicator Shut Height (Ram Down) PC Board (Ref Seating Tools 91347–[ ], 91350–[ ], and 91376–1 resting securely on, but have not fully entered, the pc board. 5. Position the seating tool onto the connector. 6. Center seating tool and header under the applicator ram of the power source you have chosen ...

Page 3

... Plc. C SEATING TOOL “A” 91350–1 5.46 [.215] 91350–2 5.18 [.204] Rev C Seating Tools 91347–[ ], 91350–[ ], and 91376–1 22.5 25.4 [.884] [1.00 “B” “C” 15.49 [.610] 25.4 [1.000] 27 ...

Page 4

... Regular inspections should be performed by quality control personnel. A record of scheduled inspections should remain with the tool or be supplied to supervisory personnel responsible for the tool. The inspection frequency should be based on the amount Seating Tools 91347–[ ], 91350–[ ], and 91376–1 26.97 29.97 [1.062] [1.180] 5.46 [.215] 15.49 [.610] Seating Tool 91376– ...