ZX-EDA41 2M Omron, ZX-EDA41 2M Datasheet
ZX-EDA41 2M
Specifications of ZX-EDA41 2M
ZXEDA412M
Related parts for ZX-EDA41 2M
ZX-EDA41 2M Summary of contents
Page 1
... M12 *1: For an average count of 4,096. *2: Models with Protective Spiral Tubes are also available. Add a suffix of “-S” to the above model numbers when ordering. (Example: ZX-ED01T-S) For detailed dimensions of the Protective Spiral Tube, refer to the information on the E39-F32A on the OMRON website. *3: Be sure to use ZX-EDA Amplifier Unit version 1,200 or later with the ZX-EV04. ...
Page 2
... Amplifier Mounting Brackets (ZX-XBE1), Instruction Manual ZX-E Series 2 Smart Sensors (Inductive Displacement Type) Setup Tool for Personal Computer Model Appearance Note 1. The ZX-SFW11EV3 or ZX-SW11EV3 is required to use the 2. The Smart Monitor Basic does not have a logging function. Cables with Connectors on Both Ends (for Model Remarks Extension) ...
Page 3
... The resolution is the deviation (±3σ) in the linear output when connected to the ZX-EDA Amplifier Unit. The above values indicate the deviations observed 30 minutes after the power is turned ON. (The resolution is measured with OMRON's standard reference object at 1/2 of the measurement range with the ZX-EDA set for the maxi- mum average count of 4,096 per period.) The resolution is given at the repeat accuracy for a stationary workpiece, and is not an indication of the distance accuracy ...
Page 4
... Measurement distance (mm) ZX-EM07MT 0.3 0.2 0.1 0 −0.1 −0.2 S50C @30 S50C @45 S50C @60 −0 Measurement distance (mm) ZX-E Series 4 Smart Sensors (Inductive Displacement Type) ZX-ED01T 0.3 0.2 0.1 0 −0.1 −0.2 −0.3 0 0.2 0.4 0.6 0.8 1 Measurement distance (mm) ZX-EV04T 0.3 0.2 0.1 0 −0.1 − ...
Page 5
... Measurement distance (mm) ZX-EV04T 0.5 S50C @60 0.4 SUS304 @60 A5052 @60 0.3 0.2 0.1 0 −0.1 −0.2 −0.3 −0.4 −5 0.0 1.0 2.0 3.0 Measurement distance (mm) ZX-E Series Smart Sensors (Inductive Displacement Type) ZX-ED02T/ZX-EM02T −1 −2 S50C @5 S50C @8 −3 S50C @12 S50C @18 −4 S50C @30 S50C @45 − ...
Page 6
... Ambient sensor head temperature (°C) ZX-E Series 6 Smart Sensors (Inductive Displacement Type) with Linearity Adjusted for Standard Sensing Object and Iron) ZX-ED01T 3.5 S50C @18 SUS304 @18 3 A5052 @18 2.5 2 1.5 1 0.5 0 0.2 ...
Page 7
... I/O Circuit Diagrams NPN Amplifier Unit: ZX-EDA11 Brown VDC White: HIGH judgement output Green: PASS judgement output Gray: LOW judgement output Blue: GND (0V) Pink: Judgement output hold input Purple: Timing input Orange: Zero reset input Red: Reset input Current output Current/voltage ...
Page 8
... Part Names Sensors ZX-EDR5T ZX-ED01T ZX-ED02T ZX-EM02T ZX-EM07MT ZX-EM02HT Preamplifier Sensor head ZX-EV04T Sensor head Preamplifier ZX-E Series 8 Smart Sensors (Inductive Displacement Type) Amplifier Units ZX-EDA11 ZX-EDA41 Display area Input cable Output cable (with connector) (with connector) Calculating Unit Output cable ...
Page 9
... Allow a warm-up period of approximately 30 minutes after turning ON the power supply. Mutual Interference Sensor Heads can be used together by connecting the ZX- CAL2 Calculating Unit between Amplifier Units. When installing Sensor Heads facing each other or in parallel, sepa- rate them by the minimum distances given in the table below. ...
Page 10
... When using a heat-resistant model like the ZX-EM02HT, develop de- signs that account for thermal expansion due to rising sensing object temperature so the sensing object will never touch the sensing sur- face ...
Page 11
... Mounting Hole Cutout Dimensions Two, M3 holes 27± 0.1 ZX-E Series Smart Sensors (Inductive Displacement Type) Vinyl-insulated round cable 5.1 dia., 9 conductors, standard length: 200 mm 13 (46) (15 dia.) Connector 15.1 Vinyl-insulated round cable 5.1 dia., 9 conductors, standard length: 200 mm ...
Page 12
... Mounting Hole Cutout Dimensions Two, M3 holes 10± 0.1 ZX-E Series 12 Smart Sensors (Inductive Displacement Type) Dimensions with Mounting Bracket Attached 22 Vinyl-insulated coaxial round cable 16.6 2.5 dia., 1 conductor, standard length M10× tightening nuts 15 dia toothed washers 15 ...
Page 13
... Two fastening nuts 72 15 dia. Toothed washer 15.6 27 58.2 133 44 15.5 dia. 13.2 Vinyl-insulated round cable 5.1 dia., standard: 100 mm ZX-E Series Smart Sensors (Inductive Displacement Type) 13 Connector Vinyl-insulated round cable 5.1 dia., 9 conductors, standard length: 200 mm 4.2 64.3 4 36.8 Vinyl-insulated round cable 5 ...
Page 14
... ZX-CAL2 Operation 24.9 indicators 3 19.5 57 15.1 54.9 12 44. 14.4 5 36.7 3.4 ZX-E Series 14 Smart Sensors (Inductive Displacement Type) ZX-XBE2 15.5 9.8 21.9 9.4 11.4 Material: Stainless steel (SUS304) Connectors 15 27± 15.5 0.1 M3×8 pan-head screw (with M3 spring washer ...
Page 15
... ZX-series Communications Interface Unit ZX-SF11 30 Cables with Connectors on Both Ends (for Extension) ZX-XC1A (1 m) ZX-XC4A (4 m) ZX-XC8A ( dia. Sensor communications indicator (communications operation) Sensor communications indicator (communications error) (336) (46) 15 13.2 Vinyl-insulation round cable, 5.23 dia. (33.1) Connector 46 Vinyl-insulated round cable, 5.2 dia., 10 conductors ...
Page 16
... CSM_5_1_1210 In the interest of product improvement, specifications are subject to change without notice. E331-E1 OMRON Corporation Industrial Automation Company Sensing Devices Division H.Q. Application Sensors Division Shiokoji Horikawa, Shimogyo-ku, ...
Page 17
... Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS ...