EEU-FA1E562 Panasonic - ECG, EEU-FA1E562 Datasheet - Page 9

• Manufacturer Part Number: EEU-FA1E562
• Description: CAP 5600UF 25V FA SER ALUM LYTIC
• Manufacturer: Panasonic - ECG
• Series: FAr

Specifications of EEU-FA1E562

• Capacitance: 5600µF
• Voltage Rating: 25V
• Tolerance: ±20%
• Lifetime @ Temp.: 5000 Hrs @ 105°C
• Operating Temperature: -55°C ~ 105°C
• Features: General Purpose
• Ripple Current: 3.735A
• Impedance: 14 mOhm
• Mounting Type: Through Hole
• Package / Case: Radial, Can
• Size / Dimension: 0.709" Dia (18.00mm)
• Height: 1.575" (40.00mm)
• Lead Spacing: 0.295" (7.50mm)
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification
• Esr (equivalent Series Resistance): -
• Surface Mount Land Size: -
• Other names: EEUFA1E562; P5662A

Design, Specifications are subject to change without notice. Ask factory for technical specifications before purchase and/or use.
Whenever a doubt about safety arises from this product, please inform us immediately for technical consulation without fail.
(3) A thorough drying after cleaning is required to
(4) Monitor the contamination levels of the cleaning
2.9 Mounting Adhesives and Coating Agents
When using mounting adhesives or coating agents to
control humidity, avoid using materials containing
h a l o g e n a t e d s o l v e n t s . A l s o , a v o i d t h e u s e o f
chloroprene based polymers.
3. Precautions for using capacitors
3.1 Environmental Conditions
C a p a c i t o r s s h o u l d not b e u s e d i n t h e f o l l o w i n g
environments.
(1) Temperature exposure above the maximum rated
(2) Direct contact with water, salt water, or oil.
(3) H i g h h u m i d i t y c o n d i t i o n s w h e r e w a t e r c o u l d
(4) Exposure to toxic gases such as hydrogen sulfide,
(5) Exposure to ozone, radiation, or ultraviolet rays.
(6) V i b r a t i o n a n d s h o c k c o n d i t i o n s e x c e e d i n g
Surface mount type
Lead type
Snap-in type
remove residual cleaning solvents which may be
trapped b e t w e e n the capacitor and the circuit
board. Avoid drying temperatures which exceed
the maximum rated temperature of the capacitor.
solvents during use by electrical conductivity, pH,
specific gravity, or water content. Chlorine levels
can rise with contamination and adversely affect
the performance of the capacitor.
Please consult us for additonal information about
After applying adhesives or coatings, dry thoroughly
to prevent residual solvents from being trapped
between the capacitor and the circuit board.
or below the minimum rated temperature of the
capacitor.
condense on the capacitor.
sulfuric acid, nitric acid, chlorine, or ammonia.
specified requirements.
acceptable cleaning solvents or cleaning methods.
Type
V(
Bi-polar SU
Bi-polar KA
Except EB
TS UP
TS HA
Series
Series
NHG
GA
KA
FB
FC
EB
TA
M
)
Cleaning permitted
L(~ 100V)
L(~ 100V)
L(~ 100V)
L(~ 100V)
L(~ 100V)
L
L
L
L
L
L
L
L
– EE21 –
3.2 Electrical Precautions
(1) Avoid touching the terminals of the capacitor as
( 2 ) A v o i d s h o r t c i r c u i t i n g t h e a r e a b e t w e e n t h e
4. Emergency Procedures
(1) I f t h e p r e s s u r e r e l i e f v e n t o f t h e c a p a c i t o r
(2) Avoid contact with the escaping electrolyte gas
5. Long Term Storage
Leakage current of a capacitor increases with long
storage times. The aluminium oxide film deteriorates
as a function of temperature and time. If used
without reconditioning, an abnormally high current
will be required to restore the oxide film. This current
surge could cause the circuit or the capacitor to fail.
Capacitor should be reconditioned by applying rated
voltage in series with a 1000
resistor for a time period of 30 minutes.
5.1 Environmental Conditions (Storage)
Capacitors should not be stored in the following
environments.
(1) Temperature exposure above 35°C or below 15 C.
(2) Direct contact with water, salt water, or oil.
(3) High humidity conditions where water could
(4) E x p o s u r e t o t o x i c g a s e s s u c h a s h y d r o g e n
(5) Exposure to ozone, radiation, or ultraviolet rays.
(6) V i b r a t i o n a n d s h o c k c o n d i t i o n s e x c e e d i n g
possible electric shock could result. The exposed
aluminium case is not insulated and could also
cause electric shock if touched.
capacitor terminals with conductive materials
including liquids such as acids or alkaline solutions.
operates, immediately turn off the equipment and
disconnect from the power source. This will
m i n i m i z e a d d i t i o n a l d a m a g e c a u s e d b y t h e
vaporizing electrolyte.
which can exceed 100 C temperatures.
If electrolyte or gas enters the eye, immediately
flush the eye with large amounts of water.
If electrolyte or gas is ingested by mouth, gargle
with water. If electrolyte contacts the skin, wash
with soap and water.
condense on the capacitor.
sulfide,sulfuric acid, nitric acid, chlorine, or
ammonia.
specified requirements.
Aluminum Electrolytic Capacitor
, current limiting
Mar. 2005