T499A225K016ATE6K0 Kemet, T499A225K016ATE6K0 Datasheet
T499A225K016ATE6K0
Specifications of T499A225K016ATE6K0
Related parts for T499A225K016ATE6K0
T499A225K016ATE6K0 Summary of contents
Page 1
... Sn Solder SPICE For a detailed analysis of specific part numbers, please visit kemet.com for a free download of KEMET's SPICE software. The KEMET SPICE program is freeware intended to aid design engineers in analyzing the performance of these capacitors over frequency, temperature, ripple, and DC bias conditions. ...
Page 2
... Refer to Part Number Electrical Specification Table ESR (100kHz) Refer to Part Number Electrical Specification Table Leakage Current ≤ 0.01CV (µA) at rated voltage after 5 minutes © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com Series 2 227 M 010 ...
Page 3
... Rated Voltage) Mil-Std-202, Meth. 213, Cond. I, 100G Peak Mechanical Shock/Vibration Mil-Std-202, Meth. 204, Cond. D, 10Hz to 2000Hz, 20G Peak *IL = Initial Limit Certification AEC-Q200 © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com Series 2 Condition ΔC/C DF DCL Characteristics Δ ...
Page 4
... Notes: (Ref) – Dimensions provided for reference only. No dimensions provided for because low profile cases do not have a bevel or a notch. * MIL-C-55365/8 specified dimensions © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com Series 2 ...
Page 5
... Also available on large (13 inch) reels. Add 7280 to the end of the part number. Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitutions will be marked with the higher voltage rating. Substitutions can include better than series. ...
Page 6
... Also available on large (13 inch) reels. Add 7280 to the end of the part number. Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitutions will be marked with the higher voltage rating. Substitutions can include better than series. ...
Page 7
... Also available on large (13 inch) reels. Add 7280 to the end of the part number. Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitutions will be marked with the higher voltage rating. Substitutions can include better than series. ...
Page 8
... E 7260-38 R 2012-12 S 3216-12 T 3528-12 U 6032-15 V 7343-20 T510X 7343-43 T510E 7260-38 © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com 2 175 mWatts @ 25°C w/+20°C Rise 75 85 110 150 165 200 125 270 285 Series ...
Page 9
... IPC standard 7351 (IPC-7351). ¹ Height of these chips may create problems in wave soldering. ² Land pattern geometry is too small for silkscreen outline. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com Rated Voltage ...
Page 10
... Case Size and X **Case Size and Z Construction MNO / Silver Paint Leadframe (-Cathode) Carbon Tantalum Wire © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com Series smax T smin 25 Pb-Free Assembly 150°C 200°C 60-120 sec 3° ...
Page 11
... In addition, packaging materials will be degraded by high temperature - reels may soften or warp, and tape peel force may increase. KEMET recommends that maximum storage temperature not exceed 40 degrees C, and maximum storage humidity not exceed 60% relative humidity. In addition, temperature fluctuations should be minimized to avoid condensation on the parts, and atmospheres should be free of chlorine and sulphur bearing compounds ...
Page 12
... Y 7343- 7343- 7260- c-spec required for 7" reel packaging. C-7280 required for 13" reel packaging. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com Series 2 7" Reel* 13" Reel* 2,500 10,000 3,000 12,000 2,500 10,000 ...
Page 13
... KPS Series product A and B are measured on a plane 0.3mm above the bottom of the pocket (f) see Addendum in EIA Document 481 for standards relating to more precise taping requirements. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com [10 pitches cumulative Po tolerance on tape ± ...
Page 14
... Tape 0.5 mm maximum 0.5 mm maximum Figure 5 – Bending Radius Embossed Punched Carrier Carrier Bending R R Radius © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com Series 2 Peel Strength Maximum Component Rotation Maximum ° ° s Rotation ( ) T ...
Page 15
... Tape Size N Min 8mm 12mm (1.969) 16mm © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com 2 Access Hole at Slot Location (Ø min.) C (Arbor hole diameter) If present, tape slot in core for tape start: 2 ...
Page 16
... Figure 8 – Maximum Camber Elongated sprocket holes (32 mm & wider tapes maximum, either direction Straight Edge 250 mm © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com 2 Carrier Tape Round Sprocket Holes START 100 mm Min. Leader ...
Page 17
... Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other measures may not be required. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com 2 Tools http://capacitoredge ...
Page 18
... Tel: 52-33-3123-2141 Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of KEMET Electronics Corporation. © ...