RPE5C2A681J2P1B03B Murata Electronics North America, RPE5C2A681J2P1B03B Datasheet - Page 2

• Manufacturer Part Number: RPE5C2A681J2P1B03B
• Description: CAP CER 680PF 100V C0G RADIAL
• Manufacturer: Murata Electronics North America
• Series: RPEr

Specifications of RPE5C2A681J2P1B03B

• Capacitance: 680pF
• Voltage - Rated: 100V
• Tolerance: ±5%
• Temperature Coefficient: C0G, NP0
• Mounting Type: Through Hole
• Operating Temperature: -55°C ~ 125°C
• Applications: General Purpose
• Package / Case: Radial
• Size / Dimension: 0.138" L x 0.197" W (3.50mm x 5.00mm)
• Thickness: 2.50mm Max
• Lead Spacing: 0.098" (2.50mm)
• Lead Style: Kinked
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Ratings: -
• Other names: 490-3664

No.
10
11
12 Solderability of Leads
13
14
RPE Series Specifications and Test Methods
Continued from the preceding page.
Terminal
Strength
Vibration
Resistance
Resistance
to
Soldering
Heat
Temperature
and
Immersion
Cycle
Item
Tensile
Strength
Bending
Strength
Appearance No defects or abnormalities
Capacitance Within the specified tolerance
Q/D.F.
Appearance No defects or abnormalities
Capacitance
Change
Dielectric
Strength
(Between
Terminals)
Appearance No defects or abnormalities
Capacitance
Change
Q/D.F.
Insulation
Resistance
Dielectric
Strength
(Between
Terminals)
Temperature Compensating Type High Dielectric Constant Type
Termination not to be broken or loosened
Termination not to be broken or loosened
30pF min.: QU1,000
30pF max.: QU400+20C
C: Nominal capacitance (pF)
Lead wire should be soldered with uniform coating on the axial
direction over 3/4 of the circumferential direction.
Within 2.5% or 0.25pF
(whichever is larger)
No defects
Within 5% or 0.5pF
(whichever is larger)
30pF min.: QU350
10pF to 30pF: QU275+5C/2
10pF max.: QU200+10C
C: Nominal capacitance (pF)
1,000M or 50M • F min.
(whichever is smaller)
No defects or abnormalities
Specifications
Char. X7R : 0.025 max.
Char. Z5U
Char. Y5V
Char. X7R : Within 7.5%
Char. Z5U
Char. Y5V
Char. X7R: Within 12.5%
Char. Z5U
Char. Y5V
Char. X7R: 0.05 max.
Char. Z5U
Char. Y5V
}
}
}
}
: 0.05 max.
: Within 20%
: Within 30%
: 0.075 max.
As in the figure, fix the capacitor body, apply the force
gradually to each lead in the radial direction of the
capacitor until reaching 10N and then keep the force
applied for 10 1 sec.
Each lead wire should be subjected to a force of 2.5N
and then bent 90 at the point of egress in one
direction. Each wire is then returned to the original
position and bent 90 in the opposite direction at the
rate of one bend per 2 to 3 sec.
The capacitor is soldered securely to a supporting
terminal and a 10 to 55Hz vibration of 1.5mm peak-
peak amplitude is applied for 6 hrs. total, 2 hrs. in each
mutually perpendicular direction. Allow 1 min. to cycle
the frequency from 10Hz to 55Hz and the converse.
The terminal of a capacitor is dipped into a 25% ethanol
(JIS-K-8101) solution of rosin (JIS-K-5902) and
then into molten solder for 2 0.5 sec. In both cases the
depth of dipping is up to about 1.5mm to 2mm from the
terminal body.
Temp. of solder: 245 5˚C Lead Free Solder (Sn-3.0Ag-0.5Cu)
The lead wire is immersed in the melted solder 1.5mm
to 2mm from the main body at 270 5 C for 3 0.5 sec.
(L3.5 x W3.0 (mm) type) or 350 10 C for 3.5 0.5 sec.
(all other types). The specified items are measured
after 24 2 hrs. (temperature compensating type) or
48 4 hrs. (high dielectric type).
• Initial measurement for high dielectric constant type
The capacitors are heat treated for 1 hr. at 150
allowed to set at room temperature for 48 4 hrs., and
given an initial measurement.
First, repeat the following temperature/time cycle 5
times :
Next, repeat twice the successive cycles of immersion,
each cycle consisting of immersion in a fresh water at
65
aqueous solution of salt at 0 3˚C for 15 min.
The capacitor is then promptly washed in running
water, dried with a drying cloth, and allowed to sit at
room temperature for 24 2 hrs. (temperature
compensating type) or 48 4 hrs. (high dielectric type).
• Initial measurement for high dielectric constant type
The capacitors are heat treated for 1 hr. at
150
4 hrs., and given an initial measurement.
–0
+5
lowest operating temperature 3˚C/30 3 min.
ordinary temperature/3 min. max.
highest operating temperature 3˚C/30 3 min.
ordinary temperature/3 min. max.
+ 0
–10
C for 15 min. and immersion in a saturated
C, allowed to sit at room temperature for 48
235 5˚C H60A or H63A Eutectic Solder
F
Test Method
Continued on the following page.
+ 0
–10
C,