500X41W224MV4E Johanson Dielectrics Inc, 500X41W224MV4E Datasheet - Page 6

• Manufacturer Part Number: 500X41W224MV4E
• Description: CAP X2Y .22UF X7R 20% 50V 1210
• Manufacturer: Johanson Dielectrics Inc
• Series: X2Y®r

Specifications of 500X41W224MV4E

• Capacitance: 0.22µF
• Voltage - Rated: 50V
• Tolerance: ±20%
• Temperature Coefficient: X7R
• Mounting Type: Surface Mount, MLCC
• Operating Temperature: -55°C ~ 125°C
• Features: Low Inductance
• Applications: Bypass, Decoupling
• Package / Case: 1210 (3225 Metric)
• Size / Dimension: 0.125" L x 0.098" W (3.18mm x 2.49mm)
• Thickness: 1.78mm Max
• Dielectric Characteristic: X7R
• Capacitance Tolerance: ± 20%
• Voltage Rating: 50VDC
• Capacitor Case Style: 1210
• No. Of Pins: 2
• Capacitor Mounting: SMD
• Operating Temperature Range: -55°C To
• Rohs Compliant: Yes
• Capacitor Application: Safety / Suppression
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Ratings: -
• Lead Spacing: -

S
X2Y
L
Ceramic capacitors (X2Y and standard MLC types) can be easily damaged when hand soldered. Thermal cracking of the ceramic
body is often invisible even under a microscope. Factors that increase thermal cracking risk:
1. 4 terminals to solder can increase hand-soldering time and temperature exposure
2. Pb-free solders have higher reflow temperatures
3. Low inductance connections to ground are inherently good heat-sinks
A damaged component may exhibit a short circuit immediately and not recover, or may operate with intermittent Insulation Resistance
(IR) levels. If you are not achieving expected results and have followed the other guidelines carefully, check to see you are adhering to
the soldering guidelines below:
• Always pre-heat the PCB and component to within 50°C of solder reflow temperature at 2°C/sec. maximum.
• Use contact-less hand solder tools such as a hot air pencil, IR lamp, etc.
• Avoid over-heating of the ceramic component, temperature limit: 260°C for 20-30 seconds max.
• Use a soldering iron as last resort; 20W max. tip, NO CONTACT with ceramic, limit solder time to 5 seconds max.
A reliable, cost effective prototype PCB reflow soldering process is possible using a household toaster oven. There are several good
procedures available on-line by googling “Toaster Oven Soldering”
O
X2Y capacitors deliver excellent performance in EMI/RFI fi ltering and Power Bypass applications. Physical and electrical placement
on the PCB is critical in achieving good results. A low inductance, dual ground connection is mandatory.
EMI Filter Applications
inductance connections and should be avoided. See detailed application note
PDN / Power Bypass Applications
recommended layout against a poor layout. Because of its long extents from
device terminals to vias, and the wide via separation, the poor layout exhibits
approximately 200% L1 inductance, and 150% L2 inductance compared to
recommended X2Y layouts. See detailed application note
Mounting.
6
OLDER
AB
G
PTIMIZING
X
Y
V
U
Z
E
VALUATION
®
0.020
0.020
0.024
0.015
0.039
0.064
Fig. 1
P
0402 (X07)
IN
Use of solder mask beneath component is not recommended because of flux/contaminant entrapment.
F
AD
ILTER
X2Y P
R
0.51
0.51
0.61
0.38
0.99
1.63
mm
ECOMMENDATIONS
S
OLDERING
ERFORMANCE ON THE
0.035
0.025
0.040
0.020
0.060
0.090
& D
0603 (X14)
IN
Low inductance PCB routing examples are shown in fi gures 1 and 2. Figures 3-5 show unbalanced and high
ECOUPLING
0.89
0.64
1.02
0.51
1.52
2.29
mm
P
RECAUTIONS
0.050
0.035
0.050
0.022
0.080
0.120
0805 (X15)
Fig. 2
IN
Figures on right compare the X2Y
1.27
0.89
1.27
0.56
2.03
3.05
mm
PCB
www.johanson dielectrics.com
C
0.065
0.040
0.080
0.040
0.120
0.160
1206 (X18)
APACITORS
IN
1.65
1.02
2.03
1.02
3.05
4.06
X2Y Power Bypass
mm
0.100
0.040
0.080
0.045
0.160
0.160
Fig. 3
1210 (X41)
IN
2.54
1.02
2.03
1.14
4.06
4.06
mm
X2Y EMI FIlter Evaluation and PCB Design
0.100
0.040
0.100
0.045
0.160
0.180
1410 (X44)
IN
2.54
1.02
2.54
1.14
4.06
4.57
mm
Recommended X2Y
Bypass Layout
Fig. 4
0.125
0.040
0.130
0.045
0.190
0.210
1812 (X43)
IN
3.18
1.02
3.30
1.14
4.83
5.33
mm
X
Y
Fig. 5
Z
V
G
V
V
V
Guidelines.
U