ISL55001 Intersil Corporation, ISL55001 Datasheet
ISL55001
Available stocks
Related parts for ISL55001
ISL55001 Summary of contents
Page 1
... 1kΩ gain of +1, the ISL55001 has a -3dB bandwidth of 220MHz with a phase margin of 50°. Because of its conventional voltage-feedback topology, the ISL55001 allows the use of reactive or non-linear elements in its feedback network. This versatility combined with low cost ...
Page 2
... MIN MAX AC Electrical Specifications V PARAMETER DESCRIPTION BW -3dB Bandwidth (V OUT GBWP Gain Bandwidth Product PM Phase Margin 2 ISL55001 = 25°C) Continuous Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . 60mA Power Dissipation (P S Operating Temperature Range (T Operating Junction Temperature (T Storage Temperature ( ±15V 1kΩ 25°C, unless otherwise specified. ...
Page 3
... L Source Power=-20dBm R =500Ω =150Ω =75Ω =-50Ω L FIGURE 3. FREQUENCY RESPONSE FOR VARIOUS + ISL55001 = + 1kΩ unless otherwise specified. (Continued CONDITION R = 100Ω ±15V ±15V, 10V step S NTSC/PAL NTSC/PAL 10kHz 10kHz = 5V ...
Page 4
... FIGURE 7. PHASE vs FREQUENCY FOR VARIOUS NON- INVERTING GAIN SETTINGS 100 R =500Ω SUPPLY VOLTAGES (±V) FIGURE 9. GAIN BANDWIDTH PRODUCT vs SUPPLY 4 ISL55001 (Continued) C =82pF L C =39pF L C =10pF L FIGURE 6. FREQUENCYRESPONSE FOR VARIOUS C LOAD FIGURE 8. PHASE vs FREQUENCY FOR VARIOUS 350 300 250 200 ...
Page 5
... Typical Performance Curves FIGURE 11. GAIN vs FREQUENCY FOR VARIOUS +1) V FIGURE 13. GAIN vs FREQUENCY FOR VARIOUS INVERTING INPUT CAPACITANCE (C FIGURE 15. COMMON-MODE REJECTION RATIO (CMRR) 5 ISL55001 (Continued) FIGURE 12. GAIN vs FREQUENCY FOR VARIOUS R FEEDBACK FIGURE 14. GAIN vs FREQUENCY FOR VARIOUS SUPPLY ) IN FIGURE 16. POWER SUPPLY REJECTION RATIO (PSRR) (A ...
Page 6
... FIGURE 17. HARMONIC DISTORTION vs FREQUENCY (A = +1) V FIGURE 19. OUTPUT SWING vs FREQUENCY FOR VARIOUS GAIN SETTINGS 20% to 80% 80% to 20% FIGURE 21. LARGE SIGNAL RISE AND FALL TIMES 6 ISL55001 (Continued) FIGURE 18. HARMONIC DISTORTION vs OUTPUT VOLTAGE FIGURE 20. OUTPUT SWING vs SUPPLY VOLTAGE FOR FIGURE 22. SMALL SIGNAL RISE AND FALL TIMES ...
Page 7
... SO8 0.6 θ =110°C/W JA 0.4 0 AMBIENT TEMPERATURE (°C) FIGURE 25. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE 7 ISL55001 (Continued =0Ω =500Ω =5pF FIGURE 24. PACKAGE POWER DISSIPATION vs AMBIENT 100 125 150 JEDEC JESD51-3 LOW EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD 1 ...
Page 8
... Power Dissipation can With the high output drive capability of the ISL55001 possible to exceed the 150°C absolute maximum junction temperature under certain load current conditions. Therefore important to calculate the maximum junction ...
Page 9
... ISL55001. A derivation of the transfer function is provided for convenience (See Figure 26). Sallen-Key High Pass Filter Again this useful filter benefits from the characteristics of the ISL55001. The transfer function is very similar to the low pass so only the results are presented (See Figure 27). - pin is S ...
Page 10
... FIGURE 28. DIFFERENTIAL OUTPUT INSTRUMENTATION AMPLIFIER 10 ISL55001 1nF OUT 1kΩ 1kΩ 1nF FIGURE 27. SALLEN-KEY HGH PASS FILTER ground potential errors inherent in remote transmission. This ...
Page 11
... Strain Gauge The strain gauge is an ideal application to take advantage of the moderate bandwidth and high accuracy of the ISL55001. The operation of the circuit is very straightforward. As the strain variable component resistor in the balanced bridge is subjected to increasing strain, its resistance changes, VARIABLE SUBJECT TO STRAIN 1kΩ ...
Page 12
... However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 12 ISL55001 FN6200.1 March 9, 2006 ...