ISL84514 Intersil Corporation, ISL84514 Datasheet

Page 1

... The ISL8451X are single-pole/single-throw (SPST) switches, with the ISL84514 being normally open (NO), and the ISL84515 being normally closed (NC). Table 1 summarizes the performance of this family. For higher performance, pin compatible versions, see the ISL43110, ISL43111 data sheet. For ± ...

Page 2

... Pinouts (Note 1) ISL84514 (SOIC) TOP VIEW COM 1 2 N.C. N. ISL84515 (SOIC) TOP VIEW COM N. NOTE: 1. Switches Shown for Logic “0” Input. Truth Table LOGIC ISL84514 0 OFF 1 ON NOTE: Logic “0” ≤ 0.8V. Logic “1” ≥ 2.4V. ...

Page 3

... COM OFF Capacitance 1MHz COM(OFF) COM ON Capacitance 1MHz, V COM(ON) 3 ISL84514, ISL84515 Thermal Information Thermal Resistance (Typical, Note SOT-23 Package . . . . . . . . . . . . . . . . . . . . . . . 8 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . Maximum Junction Temperature (Plastic Package 150 Moisture Sensitivity (See Technical Brief TB363) All Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Level 1 Maximum Storage Temperature Range -65 Maximum Lead Temperature (Soldering 10s) ...

Page 4

... COM OFF Capacitance 1MHz COM(OFF) COM ON Capacitance 1MHz, V COM(ON) POWER SUPPLY CHARACTERISTICS Positive Supply Current 13.2V ISL84514, ISL84515 TEST CONDITIONS = 0V or V+, Switch On or Off IN Test Conditions +10.8V to +13.2V, GND = 0V, V Unless Otherwise Specified TEST CONDITIONS = 1.0mA 10V COM COM = 1 ...

Page 5

... SWITCH INPUT V 90% SWITCH OUTPUT Logic input waveform is inverted for switches that have the opposite logic sense. FIGURE 1A. MEASUREMENT POINTS 5 ISL84514, ISL84515 Test Conditions +3.0V to +3.6V, GND = 0V, V Unless Otherwise Specified TEST CONDITIONS = 1.0mA 1.5V COM COM = 1.0mA 0.5V, 1V, 1.5V COM = 3V, 1V ...

Page 6

... LOGIC INPUT OFF Q = ∆ OUT L FIGURE 2A. MEASUREMENT POINTS SIGNAL GENERATOR COM ANALYZER GND R L FIGURE 3. OFF ISOLATION TEST CIRCUIT IMPEDANCE 6 ISL84514, ISL84515 (Continued FIGURE 2. CHARGE INJECTION COM ANALYZER COM GND FIGURE 5. CAPACITANCE TEST CIRCUIT V+ C ...

Page 7

... Detailed Description The ISL84514 and ISL84515 analog switches offer precise switching capability from a single 2.4V to 12V supply with low on-resistance, and high-speed operation. The devices are especially well suited to portable battery powered equipment thanks to the low operating supply voltage (2.4V), low power consumption (5µW), low leakage currents (2nA max), and the tiny SOT-23 packaging ...

Page 8

... COM FIGURE 9. CHARGE INJECTION vs SWITCH VOLTAGE 8 ISL84514, ISL84515 V+ or GND and the analog signal. This means their leakages will vary as the signal varies. The difference in the two diode leakages to the V+ and GND pins constitutes the analog- signal-path leakage current. All analog leakage current flows between each pin and one of the supply terminals, not to the other switch terminal ...

Page 9

... IN P (V+ = 12V) IN P-P P FREQUENCY (MHz) FIGURE 13. FREQUENCY RESPONSE Die Characteristics SUBSTRATE POTENTIAL (POWERED UP): GND TRANSISTOR COUNT: ISL84514: 40 ISL84515: 40 PROCESS: Si Gate CMOS 9 ISL84514, ISL84515 Unless Otherwise Specified (Continued (V COM R = 300Ω ...

Page 10

... The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 10 ISL84514, ISL84515 M8.15 (JEDEC MS-012-AA ISSUE C) 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE M ...

Page 11

... However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 11 ISL84514, ISL84515 P5.064 5 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE SYMBOL ...