S202S01 Sharp Microelectronics, S202S01 Datasheet

Page 1

... Zero cross type is also available. (S102S02 Series/ S202S02 Series) ■ Description S102S01 Series and S202S01 Series Solid State Relays (SSR) are an integration of an infrared emitting diode (IRED), a Phototriac Detector and a main output Triac. These devices are ideally suited for controlling high voltage AC loads with solid state reliability while providing 4 ...

Page 2

... Product mass : approx. 6.3g 2 S102S01 Series S202S01 Series (Unit : mm) ±0.2 ±0.3 ±0.2 ±0.2 5.5 Common to pin No.1 Epoxy resin Date code (2 digit) + − ±0.1 (2.54) 0.6 (1.4) Sheet No.: D4-A02301EN ...

Page 3

... Rank mark There is no rank mark indicator and currently there are no rank offered for this device. 2nd digit Month of production Month Mark January 1 February 2 March 3 April 4 May 5 June 6 July 7 August 8 September 9 October O November N December D 3 S102S01 Series S202S01 Series Sheet No.: D4-A02301EN ...

Page 4

... V (rms)=200V, AC50Hz D I (rms)=2A, Resistance load (j-c) Between junction and case th R (j-a) Between junction and ambient th 4 S102S01 Series S202S01 Series Soldering area (T =25˚C) a MIN. TYP. MAX. − 1.2 1.4 − − 100 − − 100 =20mA − ...

Page 5

... S102S01 Model No. S202S01 Please contact a local SHARP sales representative to see the actual status of the production. I [mA DRM (V =12V, D [V] R =30Ω) L MAX.8 400 MAX.8 600 I [mA DRM (V =12V, D [V] R =30Ω) L MAX.8 400 MAX.8 600 5 S102S01 Series S202S01 Series Sheet No.: D4-A02301EN ...

Page 6

... Fig.4 Forward Current vs. Forward Voltage 100 75 100 125 (˚C) 6 S102S01 Series S202S01 Series vertically, spread the thermal conductive silicone grease on the touch surface of the device and tighten up the device in the center of Al plate at the torque of 0.4N•m. T =100˚C a 75˚C 25˚ ...

Page 7

... T =25˚C Start 100 Fig.8 Repetitive Peak OFF-state Current vs. Ambient Temperature −4 10 −5 10 −6 10 −7 10 −8 10 − 100 (˚ S102S01 Series S202S01 Series T =25˚ RMS ON-state current I (rms)( =400V D (S102S01) V =600V D (S202S01) S102S01 S202S01 − Ambient temperature T (˚C) a Sheet No.: D4-A02301EN ...

Page 8

... Locate snubber circuit between output terminals I (rms) OUT (Cs=0.022µF, Rs=47Ω) f − T − opr ) must be 0.1mA or less increases faster than rated dV/dt, the Triac may turn on. To avoid this situation, 8 S102S01 Series S202S01 Series MIN. MAX. Unit 0 120 V 80 240 ...

Page 9

... Standard Circuit Tr1 ✩ For additional design assistance, please review our corresponding Optoelectronic Application Notes. 4.4mm MIN. S102S01 S202S01 3 1 Load SSR Line Surge absorption circuit (Snubber circuit S102S01 Series S202S01 Series Sheet No.: D4-A02301EN ...

Page 10

... Please solder within one time. Other notices Please test the soldering method in actual condition and make sure the soldering works fine, since the impact on the junction between the device and PCB varies depending on the tooling and soldering conditions. 10 S102S01 Series S202S01 Series Sheet No.: D4-A02301EN ...

Page 11

... This product shall not contain the following materials. And they are not used in the production process for this device. Regulation substances : CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform) Specific brominated flame retardants such as the PBBOs and PBBs are not used in this product at all. 11 S102S01 Series S202S01 Series Sheet No.: D4-A02301EN ...

Page 12

... Each partition should have 5 products with the lead upward. Cushioning material and molt plane should be located after all products are settled (1 packing contains 200 pcs). Package composition Molt plane Cushioning material Product Partition 12 S102S01 Series S202S01 Series Pad Packing case Sheet No.: D4-A02301EN ...

Page 13

... SHARP. Express written permission is also required before any use of this publication may be made by a third party. · Contact and consult with a SHARP representative if there are any questions about the contents of this pub- lication. 13 S102S01 Series S202S01 Series Sheet No.: D4-A02301EN ...