DSPIC30F1010-30I/SO Microchip Technology, DSPIC30F1010-30I/SO Datasheet - Page 2

• Manufacturer Part Number: DSPIC30F1010-30I/SO
• Description: IC DSPIC MCU/DSP 6K 28SOIC
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F1010-30I/SO

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 30 MIPs
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 21
• Program Memory Size: 6KB (2K x 24)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Data Bus Width: 16 bit
• Processor Series: DSPIC30F
• Core: dsPIC
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240002, DM300023, DM330011
• Package: 28SOIC W
• Device Core: dsPIC
• Family Name: dsPIC30
• Maximum Speed: 30 MHz
• Operating Supply Voltage: 3.3|5 V
• Number Of Programmable I/os: 21
• Interface Type: I2C/SPI/UART
• On-chip Adc: 6-chx10-bit
• Number Of Timers: 2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM300023 - KIT DEMO DSPICDEM SMPS BUCKDV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLE
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

dsPIC30F1010/202X
TABLE 2:
DS80445D-page 2
Note 1:
Module
PWM
PWM
PWM
PWM
PWM
PWM
PWM
PWM
PWM
PWM
PWM
ADC
ADC
ADC
ADC
ADC
Only those issues indicated in the last column apply to the current silicon revision.
SILICON ISSUE SUMMARY
Current Reset
Special Event
Temperature
Hold Circuits
Sample and
Hold Timing
Sample and
Trigger and
Conversion
Dead Time
Duty Cycle
Dead Time
Duty Cycle
PWM Pins
Operation
Individual
Interrupts
Software
Override
Override
Feature
Trigger
Enable
Priority
Trigger
Global
Under
Mode
Rate
—
Number
Item
10.
11.
12.
13.
14.
15.
16.
1.
2.
3.
4.
5.
6.
7.
8.
9.
If a value less than 0x0010 is written to the DTRx and
ALTDTRx registers, either or both of the PWMHx and
PWMLx outputs will not function.
Duty cycle resolution is not 1.1 ns over the entire duty
cycle range.
The PWM Special Event Trigger and PWM Individual
Trigger do not function near the beginning of the PWM
period.
The dead-time registers (DTRx/ALTDTRx) must be
modified only when the PWM is not running and should
not be modified “on-the-fly”.
The PWM override feature does not work correctly.
Any duty cycle value less than or equal to 0x0010
causes the PWM outputs to flip to the inverted state.
The PWM fault, current-limit and output override
priorities do not work correctly.
In Push-Pull mode, with immediate updates enabled,
the PWM pins may become swapped.
The PWM module may not operate at temperatures
below -20ºC.
The PWM output may exhibit an occasional jitter
proportional to the operating speed of the
dsPIC30F1010/202X device.
Setting the XPRES bit in the PWMCONx register
should enable a current-limit source to reset the PWM
period when the PWM generated is configured in
Independent Time Base mode. This functionality is not
working correctly.
The Global Software Trigger bit (GSWTRG in the
ADCON register) is not reset unless the PxRDY bits in
the ADSTAT register are reset.
The resolution of the PWM to ADC sample-and-hold
trigger timing is up to 41.6 ns instead of the 8 ns
specified in the device data sheet.
Individual ADC Interrupts for the ADC pin pairs do not
work.
The maximum conversion rate for the ADC module is
1.5 Msps.
Depending on conversion configuration, ADC inputs that
do not have dedicated sample-and-hold circuits may
produce inaccurate conversion results.
Issue Summary
© 2010 Microchip Technology Inc.
A1
Revisions
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Affected
A2
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
(1)
A3
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X