PIC18F2525-I/SO Microchip Technology, PIC18F2525-I/SO Datasheet - Page 189

• Manufacturer Part Number: PIC18F2525-I/SO
• Description: IC MCU FLASH 24KX16 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2525-I/SO

• Program Memory Type: FLASH
• Program Memory Size: 48KB (24K x 16)
• Package / Case: 28-SOIC (7.5mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 25
• Eeprom Size: 1K x 8
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3986 B
• Interface Type: SPI, I2C, EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 1 x 8
• Operating Supply Voltage: 4.2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DM163022, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Package: 28SOIC W
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT28SO-1 - SOCKET TRANSITION 28SOIC 300MILI3DB18F4620 - BOARD DAUGHTER ICEPIC3
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

17.4.7
In I
reload value is placed in the lower 7 bits of the
SSPADD register (Figure 17-17). When a write occurs
to SSPBUF, the Baud Rate Generator will automatically
begin counting. The BRG counts down to ‘0’ and stops
until another reload has taken place. The BRG count is
decremented twice per instruction cycle (T
Q2 and Q4 clocks. In I
reloaded automatically.
FIGURE 17-17:
TABLE 17-3:
© 2008 Microchip Technology Inc.
Note 1:
2
C Master mode, the Baud Rate Generator (BRG)
40 MHz
40 MHz
40 MHz
16 MHz
16 MHz
16 MHz
4 MHz
4 MHz
4 MHz
Fosc
The I
100 kHz) in all details, but may be used with care where higher rates are required by the application.
BAUD RATE
2
C interface does not conform to the 400 kHz I
I
2
C™ CLOCK RATE W/BRG
SSPM3:SSPM0
BAUD RATE GENERATOR BLOCK DIAGRAM
2
C Master mode, the BRG is
10 MHz
10 MHz
10 MHz
4 MHz
4 MHz
4 MHz
1 MHz
1 MHz
1 MHz
SCL
F
CY
SSPM3:SSPM0
CY
PIC18F2525/2620/4525/4620
) on the
Reload
Control
CLKO
20 MHz
20 MHz
20 MHz
F
8 MHz
8 MHz
8 MHz
2 MHz
2 MHz
2 MHz
CY
* 2
Reload
Once the given operation is complete (i.e., transmis-
sion of the last data bit is followed by ACK), the internal
clock will automatically stop counting and the SCL pin
will remain in its last state.
Table 17-3 demonstrates clock rates based on
instruction cycles and the BRG value loaded into
SSPADD.
2
BRG Down Counter
C specification (which applies to rates greater than
SSPADD<6:0>
BRG Value
1Fh
0Ch
18h
63h
09h
27h
02h
09h
00h
F
OSC
/4
(2 Rollovers of BRG)
DS39626E-page 187
400 kHz
400 kHz
333 kHz
312.5 kHz
1 MHz
100 kHz
308 kHz
100 kHz
100 kHz
F
SCL
(1)
(1)
(1)
(1)