PIC16F1946-E/PT Microchip Technology, PIC16F1946-E/PT Datasheet - Page 366

no-image

PIC16F1946-E/PT

Manufacturer Part Number
PIC16F1946-E/PT
Description
MCU 8BIT 8K FLASH 64TQFP
Manufacturer
Microchip Technology
Series
PIC® XLP™ 16Fr

Specifications of PIC16F1946-E/PT

Core Size
8-Bit
Program Memory Size
14KB (8K x 14)
Core Processor
PIC
Speed
32MHz
Connectivity
I²C, LIN, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, LCD, POR, PWM, WDT
Number Of I /o
54
Program Memory Type
FLASH
Eeprom Size
256 x 8
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 5.5 V
Data Converters
A/D 17x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
64-TFQFP
Controller Family/series
PIC16F
Eeprom Memory Size
256Byte
Ram Memory Size
512Byte
Cpu Speed
32MHz
No. Of Timers
5
Interface
EUSART, I2C, SPI
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC16F1946-E/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
PIC16F/LF1946/47
27.2
The Low-Voltage Programming Entry mode allows the
PIC16F/LF1946/47 devices to be programmed using
V
Configuration Word 2 is set to ‘1’, the low-voltage ICSP
programming entry is enabled. To disable the
Low-Voltage ICSP mode, the LVP bit must be
programmed to ‘0’.
Entry into the Low-Voltage Programming Entry mode
requires the following steps:
1.
2.
Once the key sequence is complete, MCLR must be
held at V
maintained.
If low-voltage programming is enabled (LVP = 1), the
MCLR Reset function is automatically enabled and
cannot be disabled. See Section 6.3 “MCLR” for more
information.
The LVP bit can only be reprogrammed to ‘0’ by using
the High-Voltage Programming mode.
FIGURE 27-3:
DS41414A-page 364
DD
Note:
MCLR is brought to V
A 32-bit key sequence is presented on
ICSPDAT, while clocking ICSPCLK.
only, without high voltage. When the LVP bit of
IL
Low-Voltage Programming Entry
Mode
for as long as Program/Verify mode is to be
The ICD 2 produces a V
than the maximum V
PIC16F/LF1946/47.
*
PICkit™ STYLE CONNECTOR INTERFACE
The 6-pin header (0.100" spacing) accepts 0.025" square pins.
IL
.
PP
specification of the
PP
voltage greater
Preliminary
Pin 1 Indicator
1
2
3
4
5
6
27.3
Connection to a target device is typically done
through an ICSP™ header. A commonly found
connector on development tools is the RJ-11 in the
6P6C (6 pin, 6 connector) configuration. See
Figure 27-2.
FIGURE 27-2:
Another connector often found in use with the PICkit™
programmers is a standard 6-pin header with 0.1 inch
spacing. Refer to Figure 27-3.
V
PP
V
Common Programming Interfaces
DD
/MCLR
Pin Description*
1 = V
2 = V
3 = V
4 = ICSPDAT
5 = ICSPCLK
6 = No Connect
Pin Description*
1 = V
2 = V
3 = V
4 = ICSPDAT
5 = ICSPCLK
6 = No Connect
PP
DD
SS
/MCLR
1
Target
(ground)
PP
DD
SS
2
3
/MCLR
4
(ground)
Target
5
V
6
SS
ICSPDAT
ICD RJ-11 STYLE
CONNECTOR INTERFACE
 2010 Microchip Technology Inc.
ICSPCLK
NC
Target
PC Board
Bottom Side

Related parts for PIC16F1946-E/PT