ATTINY261-15MZ Atmel, ATTINY261-15MZ Datasheet - Page 188

• Manufacturer Part Number: ATTINY261-15MZ
• Description: MCU AVR 2K FLASH 15MHZ 32-QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY261-15MZ

• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Speed: 16MHz
• Number Of I /o: 16
• Eeprom Size: 128 x 8
• Core Processor: AVR
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Program Memory Size: 2KB (2K x 8)
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Connectivity: USI
• Core Size: 8-Bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

T
Notes:
Symbol
I
V
I
188
CC
ACLK
A
ACIO
= –40°C to +125°C, V
1. All DC Characteristics contained in this data sheet are based on simulation and characterization of ATtiny261/461/861 AVR
2. “Max” means the highest value where the pin is guaranteed to be read as low.
3. “Min” means the lowest value where the pin is guaranteed to be read as high.
4. Although each I/O port can sink more than the test conditions (10mA at V
5. Although each I/O port can source more than the test conditions (10mA at V
6. Values using methods described in
7. BOD Disabled.
ATtiny261/ATtiny461/ATtiny861
Parameter
Power Supply Current
Power-down mode
Analog Comparator
Input Offset Voltage
Analog Comparator
Input Leakage Current
microcontrollers manufactured in a typical process technology. These values are preliminary values representing design tar-
gets, and will be updated after characterization of actual Automotive silicon.
ditions (non-transient), the following must be observed:
1] The sum of all IOL, for all ports, should not exceed 60mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
conditions (non-transient), the following must be observed:
1] The sum of all IOH, for all ports, should not exceed 60mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
(PRR = 0xFF) and there is no I/O drive.
CC
= 2.7V to 5.5V (unless otherwise noted)
Condition
Active 4MHz, V
Active 8MHz, V
Active 16MHz, V
Idle 4MHz, V
Idle 8MHz, V
Idle 16MHz, V
WDT enabled, V
WDT disabled, V
WDT enabled, V
WDT disabled, V
V
V
CC
CC
= 5V, 0.1V
= 5V, Vin = V
“Minimizing Power Consumption” on page
CC
CC
CC
CC
CC
CC
= 3V
= 5V
CC
CC
CC
CC
CC
= 5V
CC
< Vin < V
= 3V
= 5V
= 3V
= 5V
/2
= 5V
= 3V
= 5V
(6)
(6)
(6)
(6)
(6)
(7)
(7)
(6)
(7)
(7)
ATD On
ATD On
CC
ATD On
– 100mV
(1)
(Continued)
Min.
CC
–50
= 5V, 5mA at V
CC
36. Power Reduction is enabled
= 5V, 5mA at V
Typ.
1.45
3.96
7.16
0.25
0.96
1.91
0.12
0.13
10
4
6
CC
= 3V) under steady state con-
CC
= 3V) under steady state
Max.
0.4
1.2
2.5
10
50
30
75
45
40
50
2
6
7753F–AVR–01/11
Units
mA
mA
mA
mA
mA
mA
mV
µA
µA
µA
µA
nA