PIC16F88-E/P Microchip Technology, PIC16F88-E/P Datasheet - Page 254

• Manufacturer Part Number: PIC16F88-E/P
• Description: IC MCU FLASH 4KX14 EEPROM 18DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F88-E/P

• Core Size: 8-Bit
• Program Memory Size: 7KB (4K x 14)
• Core Processor: PIC
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 368 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 7x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 18-DIP (0.300", 7.62mm)
• Controller Family/series: PIC16F
• No. Of I/o's: 16
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 368Byte
• Cpu Speed: 20MHz
• No. Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: ACICE0202 - ADAPTER MPLABICE 18P 300 MIL
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PICmicro MID-RANGE MCU FAMILY
Register 16-2:
DS31016A-page 16-4
bit 7
bit 6
bit 5
bit 4
SSPCON: Synchronous Serial Port Control Register
bit 7
WCOL: Write Collision Detect bit
1 = The SSPBUF register is written while it is still transmitting the previous word
0 = No collision
SSPOV: Receive Overflow Indicator bit
In SPI mode:
1 = A new byte is received while the SSPBUF register is still holding the previous data. In case
0 = No overflow
In I
1 = A byte is received while the SSPBUF register is still holding the previous byte. SSPOV is a
0 = No overflow
SSPEN: Synchronous Serial Port Enable bit
In both modes, when enabled, these pins must be properly configured as input or output.
In SPI mode:
1 = Enables serial port and configures SCK, SDO, SDI, and SS as the source of the
0 = Disables serial port and configures these pins as I/O port pins
In I
1 = Enables the serial port and configures the SDA and SCL pins as the source of the
0 = Disables serial port and configures these pins as I/O port pins
CKP: Clock Polarity Select bit
In SPI mode:
1 = Idle state for clock is a high level
0 = Idle state for clock is a low level
In I
SCK release control
1 = Enable clock
0 = Holds clock low (clock stretch) (Used to ensure data setup time)
WCOL
R/W-0
2
2
2
serial port pins
serial port pins
(must be cleared in software)
of overflow, the data in SSPSR is lost. Overflow can only occur in slave mode. The user
must read the SSPBUF, even if only transmitting data, to avoid setting overflow. In master
mode the overflow bit is not set since each new reception (and transmission) is initiated by
writing to the SSPBUF register.
“don‘t care” in transmit mode. SSPOV must be cleared in software in either mode.
C mode:
C mode:
C mode:
SSPOV
R/W-0
SSPEN
R/W-0
R/W-0
CKP
SSPM3
R/W-0
SSPM2
R/W-0
1997 Microchip Technology Inc.
SSPM1
R/W-0
bit 0
SSPM0
R/W-0