PIC18F6722-I/PT Microchip Technology, PIC18F6722-I/PT Datasheet - Page 5

• Manufacturer Part Number: PIC18F6722-I/PT
• Description: IC PIC MCU FLASH 64KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F6722-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 128KB (64K x 16)
• Package / Case: 64-TFQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 54
• Eeprom Size: 1K x 8
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3936 B
• Interface Type: SPI/I2C/EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 5
• Operating Supply Voltage: 4.2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM183032, DM183022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12-ch x 10-bit
• Package: 64TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA180020 - MODULE PLUG-IN HPC EXPL 18F87J11XLT64PT5 - SOCKET TRAN ICE 64MQFP/TQFPAC164319 - MODULE SKT MPLAB PM3 64TQFPDV007003 - PROGRAMMER UNIVERSAL PROMATE II
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

8. Module: BOD
TABLE 2:
9. Module: EUSART
10. Module: EUSART
11. Module: EUSART
© 2006 Microchip Technology Inc.
D005 V
The BOD module may reset below the minimum
operating voltage of the device when configured
for BORV1:BORV0 = 11. The updated Reset
voltage specifications are shown in bold in
Table 2.
Work around
Use the next higher BOD voltage setting to ensure
a low V
Date Codes that pertain to this issue:
All engineering and production devices.
When performing back-to-back transmission in 9-bit
mode (TX9D bit in the TXSTAx register is set), the
second byte may be corrupted if it is written into
TXREGx immediately after the TMRT bit is set.
Work around
Execute a software delay, at least one-half the
transmission’s bit time, after TMRT is set and prior
to writing subsequent bytes into TXREGx.
Date Codes that pertain to this issue:
All engineering and production devices.
The EUSART auto-baud feature may periodically
measure the incoming baud rate incorrectly. The
rate of incorrect baud rate measurements will
depend on the frequency of the incoming
synchronization byte and the system clock
frequency.
Work around
None.
In Synchronous mode (SYNC = 1) with clock
polarity high (SCKP = 1), the EUSART transmits a
shorter than expected clock on the CKx pin for the
last bit transmitted.
Work around
None.
BOR
DD
Brown-out Reset Voltage
PIC18LF6627/6722/8627/8722
BORV1:BORV0 = 11 N/A 2.05 N/A V
is detected above 2.0V.
BROWN-OUT RESET VOLTAGE
PIC18F6627/6722/8627/8722
12. Module: EUSART
13. Module: EUSART
14. Module: EUSART
15. Module: ECCP
In Synchronous mode, EUSART baud rates using
SPBRGx values of ‘0’ and ‘1’ may not function
correctly.
Work around
Use another baud rate configuration to generate
the desired baud rate.
After the last received byte has been read from the
EUSART receive buffer, RCREGx, the value is no
longer valid for subsequent read operations. The
RCREGx register should only be read once for
each byte received.
Work around
After each byte is received from the EUSART, store
the byte into a user variable. To determine when a
byte is available to read from RCREGx, poll the
RCIDL (BAUDCONx<6>) bit for a low-to-high
transition or use the EUSART receive interrupt,
RCxIF (PIRx<5>).
In 9-Bit Asynchronous Full-Duplex Receive mode,
received data may be corrupted if the TX9D bit
(TXSTAx<0>) is not modified immediately after
RCIDL (BAUDCONx<6>) is set.
Work around
Only write to TX9D when a reception is not in
progress (RCIDL = 1). No interrupt is associated
with RCIDL, therefore, it must be polled in software
to determine when TX9D can be updated.
PIC18F6XXX
CONFIG3L, is not unimplemented and will switch
the ECCP2 output pin similar to the PIC18F8XXX
devices if the Processor mode does not select
Microcontroller mode.
Work around
In MPLAB
as its PIC18F8XXX equivalent and assign the
Processor mode bits (PM<1:0>) to ‘11’ for
Microcontroller mode.
®
IDE, program the PIC18F6XXX device
device’s
Configuration
DS80221C-page 5
Word,