C8051F367-GM Silicon Laboratories Inc, C8051F367-GM Datasheet - Page 285

• Manufacturer Part Number: C8051F367-GM
• Description: IC 8051 MCU 32K FLASH 28-QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F36xr

Specifications of C8051F367-GM

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 28-QFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 25
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 17x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: I2C/SMBus/SPI/UART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: KSK-SL-TOOLSTICK, PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F360DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 21-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Package: 28QFN EP
• Device Core: 8051
• Family Name: C8051F36x
• Maximum Speed: 50 MHz
• Operating Supply Voltage: 3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1410 - KIT DEV FOR C8051F360 FAMILY
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1649

This read-only register returns the 8-bit revision ID: 0x00 (Revision A) or 0x01 (Revision B).
Bits7–0
Bits7–0: FPDAT: C2 Flash Programming Data Register.
C2 Address:
C2 Address:
C2 Address:
Bit7
Bit7
Bit7
C2 Register Definition 24.4. FPCTL: C2 Flash Programming Control
C2 Register Definition 24.5. FPDAT: C2 Flash Programming Data
FPCTL: Flash Programming Control Register.
This register is used to enable Flash programming via the C2 interface. To enable C2 Flash
programming, the following codes must be written in order: 0x02, 0x01. Note that once C2
Flash programming is enabled, a system reset must be issued to resume normal operation.
This register is used to pass Flash commands, addresses, and data during C2 Flash
accesses. Valid commands are listed below.
Code
0x06 Flash Block Read
0x07 Flash Block Write
0x08 Flash Page Erase
0x03 Device Erase
0x01
0x02
0xB4
Bit6
Bit6
Bit6
C2 Register Definition 24.3. REVID: C2 Revision ID
Bit5
Bit5
Bit5
Bit4
Bit4
Bit4
Command
C8051F360/1/2/3/4/5/6/7/8/9
Rev. 1.0
Bit3
Bit3
Bit3
Bit2
Bit2
Bit2
Bit1
Bit1
Bit1
Bit0
Bit0
Bit0
00000000
00000000
00000000
Reset Value
Reset Value
Reset Value
285