MCF52233CAL60 Freescale Semiconductor, MCF52233CAL60 Datasheet - Page 35

• Manufacturer Part Number: MCF52233CAL60
• Description: IC MCU 256K FLASH 60MHZ 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: MCF5223xr

Specifications of MCF52233CAL60

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 60MHz
• Connectivity: Ethernet, I²C, SPI, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 73
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 112-LQFP
• Cpu Family: MCF5223x
• Device Core: ColdFire
• Device Core Size: 32b
• Frequency (max): 60MHz
• Interface Type: I2C/QSPI/UART
• Total Internal Ram Size: 32KB
• # I/os (max): 56
• Number Of Timers - General Purpose: 10
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• On-chip Adc: 8-chx12-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 112
• Package Type: LQFP
• Processor Series: MCF522x
• Core: ColdFire V2
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Maximum Clock Frequency: 60 MHz
• Number Of Programmable I/os: 56
• Number Of Timers: 10
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JLINK-CF-BDM26, EWCF
• Development Tools By Supplier: M52235EVB, M52233DEMO
• Minimum Operating Temperature: - 40 C
• Package: 112LQFP
• Family Name: MCF5223x
• Maximum Speed: 60 MHz
• Operating Supply Voltage: 3.3 V
• For Use With: M52233DEMO - BOARD DEMO FOR MCF52233
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

7
8
9
10
11
2.5
GPIO can be configured for certain pins of the QSPI, timers, UARTs, FEC, and interrupts. When in GPIO mode, the timing
specification for these pins is given in
The GPIO timing is met under the following load test conditions:
Freescale Semiconductor
This value has been updated
Load capacitance determined from crystal manufacturer specifications and include circuit board parasitics.
Assuming a reference is available at power up, lock time is measured from the time V
negating. If the crystal oscillator is the reference for the PLL, the crystal start up time must be added to the PLL lock time to
determine the total start-up time.
Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum f
Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise
injected into the PLL circuitry via V
for a given interval
Based on slow system clock of 40 MHz measured at f
Num
G1
G2
G3
G4
•
•
50 pF / 50  for high drive
25 pF / 25  for low drive
General Purpose I/O Timing
CLKOUT high to GPIO output invalid
CLKOUT high to GPIO input invalid
CLKOUT high to GPIO output valid
GPIO input valid to CLKOUT high
GPIO Outputs
GPIO Inputs
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 10
Characteristic
CLKOUT
DDPLL
Table 26
and V
and
SSPLL
Table 26. GPIO Timing
Figure 6. GPIO Timing
G3
Figure
and variation in crystal oscillator frequency increase the C
sys
max.
6.
G1
G4
Symbol
t
t
CHPOV
t
CHPOI
t
PVCH
CHPI
G2
DD
and V
Min
1.5
1.5
—
9
DDPLL
Electrical Characteristics
are valid to RSTO
Max
10
—
—
—
jitter
percentage
sys
.
Unit
ns
ns
ns
ns
35