MC68HC908GT16CFB Freescale Semiconductor, MC68HC908GT16CFB Datasheet - Page 42

• Manufacturer Part Number: MC68HC908GT16CFB
• Description: IC MCU 16K FLASH 8MHZ SPI 44PQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC68HC908GT16CFB

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 36
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Memory
In applications that require more than 1000 program/erase cycles, use the 4 ms page erase specification
to get improved long-term reliability. Any application can use this 4 ms page erase specification. However,
in applications where a Flash location will be erased and reprogrammed less than 1000 times, and speed
is important, use the 1 ms page erase specification to get a shorter cycle time.
2.6.4 Flash Mass Erase Operation
Use the following procedure to erase the entire Flash memory to read as a 1:
42
10. After time, t
10. After time, t
1. When in monitor mode, with security sequence failed (see
1. Set the ERASE bit and clear the MASS bit in the Flash control register.
2. Read the Flash block protect register.
3. Write any data to any Flash location within the address range of the block to be erased.
4. Wait for a time, t
5. Set the HVEN bit.
6. Wait for a time, t
7. Clear the ERASE bit.
8. Wait for a time, t
9. Clear the HVEN bit.
1. Set both the ERASE bit and the MASS bit in the Flash control register.
2. Read the Flash block protect register.
3. Write any data to any Flash address
4. Wait for a time, t
5. Set the HVEN bit.
6. Wait for a time, t
7. Clear the ERASE and MASS bits.
8. Wait for a time, t
9. Clear the HVEN bit.
of any Flash address.
Programming and erasing of Flash locations cannot be performed by code
being executed from the Flash memory. While these operations must be
performed in the order as shown, but other unrelated operations may occur
between the steps.
A page erase of the vector page will erase the internal oscillator trim values
at $FF80 and $FF81.
Mass erase is disabled whenever any block is protected (FLBPR does not
equal $FF).
Programming and erasing of Flash locations cannot be performed by code
being executed from the Flash memory. While these operations must be
RCV
RCV
MC68HC908GT16 • MC68HC908GT8 • MC68HC08GT16 Data Sheet, Rev. 5.0
(typical 1 μs), the memory can be accessed in read mode again.
(typical 1 μs), the memory can be accessed in read mode again.
NVS
Erase
NVH
NVS
MErase
NVHL
(minimum 10 μs).
(minimum 10 μs).
(minimum 5 μs).
(minimum 1 ms or 4 ms).
(minimum 100 μs).
(minimum 4 ms).
(1)
within the Flash memory address range.
CAUTION
NOTE
NOTE
NOTE
19.3.2
Security), write to the Flash block protect register instead
Freescale Semiconductor