PTGL09AR390N0B52A0 Murata Electronics North America, PTGL09AR390N0B52A0 Datasheet - Page 79

• Manufacturer Part Number: PTGL09AR390N0B52A0
• Description: THERM 39 OHM 250V PTC RADIAL
• Manufacturer: Murata Electronics North America
• Series: PTGLr

Specifications of PTGL09AR390N0B52A0

• Voltage - Max: 250V
• Current - Hold (ih) (max): 115mA
• Current - Trip (it): 245mA
• Current - Max: 600mA
• Package / Case: Radial
• Lead Free Status / RoHS Status: Lead free by exemption / RoHS compliant by exemption
• R Min/max: -
• Time To Trip: -
• Other names: 490-4809-3

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
No.
10 High Temperature Load
(*) The resistance measurement after the test.
(**) Above mentioned soldering is done following condition at our side.
1
2
3
4
5
6
7
8
9
• Glass-Epoxy PC board
• Standard land dimensions
• Recommendable solder paste
• Recommendable solder profile
PRF18_RB5RB Series
It is measured by applying voltage less than 1.5VDC.
(by a direct current less than 10mA.) after left at 25 2 C for 2 hours.
Above conditions are mentioned in Notice.
Resistance Value
Adhesive Strength
Vibration Resistance
Solderability
Soldering Heat Resistance
Dry Heat Resistance
Cold Resistance
Temperature Cycling
Damp Heat Resistance
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
For Overheat Sensing Chip Tight Tolerance Type Specifications and Test Methods
Item
The resistance value shall be within the specified
tolerance.
There is no detachment sign of electrode.
Normal appearance
Resistance change: not exceed 20% (*)
Min. 95% electrode is covered with new solder.
Resistance change: not exceed 20% (*)
Resistance change: not exceed 20% (*)
Normal appearance
Resistance change: not exceed 20% (*)
Sensing temperature change: not exceed 1 C
Specification
After applying max. operating voltage for 3 minutes and
leaving for 2 hours in 25 C, measured by applying voltage less
than 1.5VDC. (by a direct current less than 10mA).
EIAJ ET-7403 term 9
Prepare soldered PTC to PCB (**)
and add the force of 5.0N in the direction as shown below.
(PTC=POSISTORr)
JIS C 5102 term 8.2
Soldered PTC to PCB (**)
JIS C 60068-2-20(1996)
JIS C 60068-2-20 (1996)
Soldered PTC to PCB. (**)
150 2 C leave for 1000 12 hours
Soldered PTC to PCB. (**)
-20 3 C leave for 1000 12 hours
JIS C 5102 term 9.3
Soldered PTC to PCB. (**)
+40 2 C, 90-95%RH leave for 500 8 hours
Soldered PTC to PCB. (**)
85 2 C (in air), load max. operating voltage
for 1000 12 hours
Vibration: 10-55-10Hz (1 min.)
Width: 1.5mm
Vibrate for 2 hours. in each of 3 mutually
perpendicular plane for a total of 6 hours
Solder temp.: 230 5 C
Solder: Sn63%/Pb37% (or 60%/40%)
Soaking time: 3 0.5 seconds
Soaking position: Until a whole electrode is soaked.
Solder temp.: 260 5 C
Solder: Sn63%/Pb37% (or 60%/40%)
Flax: containing less than 0.2wt% of chlorine
Soaking time: 10 0.5 seconds
Soaking position: Until a whole electrode is soaked.
Preheating: 150 5 C, 3 minutes
Soldered PTC to PCB. (**)
Times: 5 cycles
Step
1
2
3
4
room temp.
room temp.
Temp. ( C)
+150+3, -0
-20+0, -3
Test Condition
PTC
F
Time (min.)
10 to 15
10 to 15
30
30
Glass Epoxy PCB
F
R90E.pdf
77
10.3.4
11