MAXQ3183-KIT Maxim Integrated Products, MAXQ3183-KIT Datasheet - Page 20

• Manufacturer Part Number: MAXQ3183-KIT
• Description: KIT EV REFRNC DSIGN FOR MAXQ3183
• Manufacturer: Maxim Integrated Products
• Series: MAXQ®r

Specifications of MAXQ3183-KIT

• Main Purpose: Power Management, Energy/Power Meter
• Embedded: No
• Utilized Ic / Part: MAXQ3183
• Primary Attributes: Polyphase AFE
• Secondary Attributes: SPI Interface
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 90-M3183-KIT

Low-Power, Multifunction, Polyphase AFE
with Harmonics and Tamper Detect
During an SPI transfer, data is simultaneously transmit-
ted and received over two serial data lines (MISO and
MOSI) with respect to a single serial shift clock (SCLK).
The polarity and phase of the serial shift clock are the
primary components in defining the SPI data transfer
format. The polarity of the serial clock corresponds to
the idle logic state of the clock line and, therefore, also
defines which clock edge is the active edge. To define
a serial shift clock signal that idles in a logic-low state
(active clock edge = rising), the clock polarity select
(CKPOL; R_SPICF.0) bit should be configured to a 0,
while setting CKPOL = 1 causes the shift clock to idle in
a logic-high state (active clock edge = falling). The
phase of the serial clock selects which edge is used to
sample the serial shift data. The clock phase select
(CKPHA; R_SPICF.1) bit controls whether the active or
Figure 4a. SPI Interface Timing (CKPHA = 0)
Figure 4b. SPI Interface Timing (CKPHA = 1)
20
______________________________________________________________________________________
SCLK (CKPOL = 0)
SCLK (CKPOL = 1)
SCLK (CKPOL = 0)
SCLK (CKPOL = 1)
(FOR REFERENCE)
*NOT DEFINED BUT NORMALLY MSB OF CHARACTER JUST RECEIVED.
(FOR REFERENCE)
*NOT DEFINED BUT NORMALLY LSB OF PREVIOUSLY TRANSMITTED CHARACTER.
SSEL (TO SLAVE)
SSEL (TO SLAVE)
(FROM MASTER)
(FROM MASTER)
SCLK CYCLE #
(FROM SLAVE)
SCLK CYCLE #
(FROM SLAVE)
MOSI
MISO
MOSI
MISO
*
MSB
MSB
1
MSB
MSB
1
2
6
2
6
6
6
3
5
3
5
5
5
4
4
4
4
4
4
inactive clock edge is used to latch the data. When
CKPHA is set to a logic 1, data is sampled on the inac-
tive clock edge (clock returning to the idle state). When
CKPHA is set to a logic 0, data is sampled on the active
clock edge (clock transition to the active state).
Together, the CKPOL and CKPHA bits allow four possi-
ble SPI data transfer formats.
Transfers over the SPI interface always start with the
most significant bit and end with the least significant
bit. All SPI data transfers to and from the MAXQ3183
are always 8 bits (one byte) in length. The MAXQ3183
SPI interface does not support 16-bit character lengths.
The default format (upon power-up or system reset) for
the MAXQ3183 SPI interface is represented in
Figure 4a (CKPOL = 0; CKPHA = 0). In this format, the
5
3
5
3
3
3
6
2
6
2
2
2
7
1
7
1
1
1
LSB
LSB
8
LSB
8
LSB
*