LMX9838SB/NOPB National Semiconductor, LMX9838SB/NOPB Datasheet - Page 21

• Manufacturer Part Number: LMX9838SB/NOPB
• Description: IC MODULE BLUETOOTH PORT 70LTCC
• Manufacturer: National Semiconductor

Specifications of LMX9838SB/NOPB

• Frequency: 2.4GHz
• Data Rate - Maximum: 704kbps
• Modulation Or Protocol: Bluetooth v2.0, Class 2
• Applications: PDA's, POS Terminals
• Power - Output: 0dBm
• Sensitivity: -80dBm
• Voltage - Supply: 2.5 V ~ 3.6 V
• Current - Receiving: 65mA
• Current - Transmitting: 65mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: On-Board, Chip
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 70-LTCC
• Physical Interfaces: UART
• Data Rate: 704Kbps
• Operating Temperature Range: -40°C To +85°C
• Msl: MSL 4 - 72 Hours
• Frequency Max: 2480MHz
• Filter Terminals: SMD
• Frequency Min: 2402MHz
• No. Of Pins: 70
• Rohs Compliant: Yes
• For Use With: LMX9838DONGLE - KIT DESIGN DONGLE FOR LMX9838
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Compliant
• Other names: LMX9838SB

Read Local Name
Write Local Name
Read Local BDADDR
Change Local BDADDR Change Local BDADDR Confirm Note: The BDADDR is programmed by NSC. It can not be retrieved if
Store Class of Device
Set Scan Mode
Get Fixed Pin
Set Fixed Pin
Get Security Mode
Set Security Mode
Remove Pairing
List Paired Devices
Set Default Link Timeout Set Default Link Timeout Confirm Store default link supervision timeout
Get Default Link Timeout Get Default Link Timeout Confirm Get stored default link supervision timeout
Force Master Role
Store generic SDP Record
Enable SDP Record
Delete All SDP Records
Ports to Open
Set Default Audio Settings
Get Default Audio Settings
Set Event Filter
Get Event Filter
Read RSSI
Change UART Speed
Change UART Settings
Test Mode
Restore Factory Settings
Reset
Firmware Upgrade
Set Clock Frequency
Get Clock Frequency
Set PCM Slave Configuration Set PCM Slave Configuration Confirm Write the PCM Slave Configuration in the NVS
Write ROM Patch
Read Memory
Write Memory
Command
Command
Command
Read Local Name Confirm
Write Local Name Confirm
Read Local BDADDR Confirm
Store Class of Device Confirm
Set Scan Mode Confirm
Set Scan Mode Indication
Get Fixed Pin Confirm
Set Fixed Pin Confirm
PIN request
Get Security Mode Confirm
Set Security Mode Confirm
Remove Pairing Confirm
List of Paired Devices
Force Master Role Confirm
Set Default Audio Settings Confirm
Get Default Audio Settings Confirm
Set Event Filter Confirm
Get Event Filter Confirm
Read RSSI Confirm
Change UART Speed Confirm
Change UART Settings Confirm
Test Mode Confirm
Restore Factory Settings Confirm
Dongle Ready
Set Clock Frequency Confirm
Get Clock Frequency Confirm
Write ROM Patch Confirm
Read Memory Confirm
Write Memory Confirm
Store SDP Record Confirm
Enable SDP Record Confirm
Delete All SDP Records Confirm
Ports to Open Confirmed
Event
TABLE 24. Local Service Database Configuration
TABLE 25. Local Hardware Commends
TABLE 23. Local Bluetooth Settings
Event
Event
Read actual friendly name of the device
Set the friendly name of the device
erased!
Change mode for discoverability and connectability
Reports end of Automatic limited discoverable mode
Reads current PinCode stored within the device
Set the local PinCode
a PIN code is requested during authentication of an ACL link
Get actual Security mode
Configure Security mode for local device (default 2)
Remove pairing with a remote device
Get list of paired devices stored in the LMX9838 data memory
Enables/Disables the request for master role at incoming connections
21
Configure Default Settings for Audio Codec and Air Format,
stored in NVS
Get stored Default Audio Settings
Configures the reporting level of the command interface
Get the status of the reporting level
Returns an indicator for the incoming signal strength
Set specific UART speed; needs proper ISEL pin setting
Change configuration for parity and stop bits
Enable Bluetooth, EMI test, or local loopback
Soft reset
Stops the bluetooth firmware and executes the In-system-
programming code
Write Clock Frequency setting in the NVS
Read Clock Frequency setting from the NVS
Store ROM Patch in the Simply Blue module
Read from the internal RAM
Write to the internal RAM
Create a new service record within the service database
Enable or disable SDP records
Specify the RFComm Ports to open on startup
Description
Description
Description
www.national.com