ATMEGA128RFA1-ZU Atmel, ATMEGA128RFA1-ZU Datasheet - Page 90
ATMEGA128RFA1-ZU
Manufacturer Part Number
ATMEGA128RFA1-ZU
Description
IC AVR MCU 2.4GHZ XCEIVER 64QFN
Manufacturer
Atmel
Series
ATMEGAr
Datasheets
1.ATMEGA128-16AU.pdf
(385 pages)
2.ATAVR128RFA1-EK1.pdf
(13 pages)
3.ATAVR128RFA1-EK1.pdf
(555 pages)
4.ATMEGA128RFA1-ZU.pdf
(524 pages)
Specifications of ATMEGA128RFA1-ZU
Frequency
2.4GHz
Data Rate - Maximum
2Mbps
Modulation Or Protocol
802.15.4 Zigbee
Applications
General Purpose
Power - Output
3.5dBm
Sensitivity
-100dBm
Voltage - Supply
1.8 V ~ 3.6 V
Current - Receiving
12.5mA
Current - Transmitting
14.5mA
Data Interface
PCB, Surface Mount
Memory Size
128kB Flash, 4kB EEPROM, 16kB RAM
Antenna Connector
PCB, Surface Mount
Operating Temperature
-40°C ~ 85°C
Package / Case
64-VFQFN, Exposed Pad
Rf Ic Case Style
QFN
No. Of Pins
64
Supply Voltage Range
1.8V To 3.6V
Operating Temperature Range
-40°C To +85°C
Svhc
No SVHC (15-Dec-2010)
Rohs Compliant
Yes
Processor Series
ATMEGA128x
Core
AVR8
Data Bus Width
8 bit
Program Memory Type
Flash
Program Memory Size
128 KB
Data Ram Size
16 KB
Interface Type
JTAG
Maximum Clock Frequency
16 MHz
Number Of Programmable I/os
38
Number Of Timers
6
Operating Supply Voltage
1.8 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
EWAVR, EWAVR-BL
Development Tools By Supplier
ATAVR128RFA1-EK1
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATMEGA128RFA1-ZU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATMEGA128RFA1-ZUR
Manufacturer:
ON
Quantity:
56 000
- ATMEGA128-16AU PDF datasheet
- ATAVR128RFA1-EK1 PDF datasheet #2
- ATAVR128RFA1-EK1 PDF datasheet #3
- ATMEGA128RFA1-ZU PDF datasheet #4
- Current page: 90 of 555
- Download datasheet (6Mb)
9.8.3.2 Antenna Diversity Application Example
90
ATmega128RFA1
Antenna Diversity uses two antennas to switch to the most reliable RF signal path. This
is done by the radio transceiver during RX_LISTEN and RX_AACK_ON state without
interaction of the application software. Both antennas should be carefully separated
from each other to ensure highly independent receive signals.
Antenna Diversity can be used in Basic and Extended Operating Modes and can also
be combined with other features and operating modes like High Data Rate Mode and
RX/TX Indication.
A block diagram for an application using an antenna switch is shown in the following
figure.
Figure 9-33. External Antenna Diversity – Block Diagram
Generally, the Antenna Diversity algorithm is enabled with bit ANT_DIV_EN=1 in
register ANT_DIV. For the External Antenna Diversity the control of the antenna switch
(SW1) must be enabled by bit ANT_EXT_SW_EN of register ANT_DIV. Under this
condition the control pins DIG1 and DIG2 are configured as outputs. DIG1 and DIG2
are used to feed the antenna switch signal and its inverse to the differential inputs of the
RF Switch (SW1).
The selected antenna is indicated by bit ANT_SEL of register ANT_DIV. The antenna
selection continues searching for new frames on both antennas after the frame
reception is completed. However the register bit ANT_SEL maintains its previous value
(from the last received frame) until a new SHR has been found and the selection
algorithm locked into one antenna again. Then the register bit ANT_SEL is updated.
The antenna defined by the ANT_CTRL bits of register ANT_DIV is selected for
transmission. If for example the same antenna as selected for reception is to be used
for transmission, the antenna must be set using the ANT_CTRL bits based on the value
read from the ANT_SEL bit. It is recommended to read bit ANT_SEL after the
TRX24_RX_START interrupt.
The autonomous search and selection allows the use of Antenna Diversity during
reception even if the application software currently does not control the radio
transceiver for instance in Extended Operating Mode.
An application software defined selection of a certain antenna can be done by disabling
the automatic Antenna Diversity algorithm (ANT_DIV_EN = 0) and selecting one
antenna using register bit ANT_CTRL.
A N T 0
A N T 1
S W 1
B 1
10
1
2
7
8
9
...
...
A V S S
R F P
R F N
A V S S
D IG 2
D IG 4
1 4
A T m ega 128R FA 1
1 5
8266B-MCU Wireless-03/11
Related parts for ATMEGA128RFA1-ZU
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Microcontroller with 128K bytes In-system programmable flash, 8 MHz, power supply =2.7 - 5.5V
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
IC AVR MCU 128K 16MHZ 5V 64TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC AVR MCU 128K 16MHZ 5V 64-QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC AVR MCU 128K 16MHZ COM 64-QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC AVR MCU 128K 16MHZ 64-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC AVR MCU 128K 16MHZ 64-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC AVR MCU 128K 16MHZ IND 64-QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU AVR 128KB FLASH 16MHZ 64TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU AVR 128KB FLASH 16MHZ 64QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU AVR 128KB FLASH 16MHZ 64TQFP
Manufacturer:
Atmel
Datasheet: