ISL85033DUALEVAL1Z Intersil, ISL85033DUALEVAL1Z Datasheet

no-image

ISL85033DUALEVAL1Z

Manufacturer Part Number
ISL85033DUALEVAL1Z
Description
EVAL BOARD 1 FOR ISL85033
Manufacturer
Intersil
Datasheets

Specifications of ISL85033DUALEVAL1Z

Lead Free Status / RoHS Status
Lead free / RoHS Compliant
November 29, 2010
AN1574.2
ISL85033DUALEVAL1Z Wide VIN Dual Standard
Buck Regulator With 3A/3A Output Current
Description
The ISL85033DUALEVAL1Z kit is intended for use by
individuals with requirements for Point-of-Load
applications sourcing from 4.5V to 28V. The
ISL85033DUALEVAL1Z evaluation board is used to
demonstrate the performance of the ISL85033 wide VIN
dual standard buck regulator with 3A/3A output
current converter.
The ISL85033 is offered in a 4mmx4mm 28 Ld TQFN
package with 1mm maximum height. The complete
converter occupies 6.25cm
Key Features
• Wide Input Voltage Range from 4.5V to 28V
• Adjustable Output Voltage with Continuous Output
• Current Mode Control
• Adjustable Switching Frequency from 300kHz to 2MHz
• Independent Power-Good Detection
• Selectable In-Phase or Out-of-Phase PWMs Switching
• Independent, Sequential, Ratiometric or Absolute
• Internal 2ms Soft-start Time
• Overcurrent and Hiccup Mode Short Circuit
• Boot Undervoltage Detection
• Channels are Out-of-phase, Reducing Voltage Ripple
Recommended Equipment
The following materials are recommended to perform
testing:
• 0V to 30V Power Supply with at least 7A source
• Electronic Loads capable of sinking current up to 7A
• Digital Multimeters (DMMs)
• 100MHz quad-trace oscilloscope
• Signal generator
Current up to 3A
Operation
Tracking Between Outputs
Protection, Thermal Overload Protection, UVLO
and Component Size
current capability or 5V battery
1-888-INTERSIL or 1-888-468-3774
2
1
area.
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
|
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
Application Note 1574
Quick Setup Guide
Evaluating the Other Output Voltage
The ISL85033DUALEVAL1Z kit outputs are preset to 5V
for V
can be adjusted from 0.8V to 5V. The output voltage
programming resistor, R3 (or R14 in Channel 2), will
depend on the desired output voltage of the regulator
and the value for the feedback resistor R2 (R16
respectively), as shown in Equation 1.
If the output voltage desired is 0.8V, then R3 (R14
respectively) is shorted. The value for R2 (R16
respectively) is typically between 1k and 10k. Please
note that if VOUT is less than 2.5V, the switching
frequency and compensation must be changed for
300kHz operation due to minimum on-time limitation.
Please refer to the data sheet for further information
(FN6676).
Frequency Control
ISL85033 has an FS pin that controls the frequency of
operation. Programmable frequency allows for
optimization between efficiency and external
component size. Default switching frequency is 500kHz
when FS is tied to VCC (R9 = 0). By removing R9 and
connecting R10 to ground, the switching frequency
could be changed from 300kHz (R10 = 383k) to 2MHz
(R10 = 40.2k). Please refer to the data sheet
(FN6676) for calculating the value of R10. Do not leave
this pin floating.
R3
R14
1. Ensure that the circuit is correctly connected to the
2. Connect the bias supply to VIN1, the plus terminal
3. Verify that the position is ON for S1 and S2.
4. Turn on the power supply.
5. Verify the output voltage is 5V for V
All other trademarks mentioned are the property of their respective owners.
supply and loads prior to applying any power.
to VIN1 and the negative return to GND2.
for V
=
OUT1
=
(
V
(
V
OUT1
OUT2.
OUT2
and 3.3V for V
V
Copyright Intersil Americas Inc. 2010. All Rights Reserved.
V
FB
FB
) R2 V
) R16 V
OUT2
FB
FB
; however, output voltages
Author: Paul Orfanu
OUT1
and 3.3V
(EQ. 1)

Related parts for ISL85033DUALEVAL1Z

ISL85033DUALEVAL1Z Summary of contents

Page 1

... Turn on the power supply. 5. Verify the output voltage is 5V for V for V OUT2. Evaluating the Other Output Voltage The ISL85033DUALEVAL1Z kit outputs are preset to 5V for V and 3.3V for V OUT1 can be adjusted from 0.8V to 5V. The output voltage programming resistor, R3 (or R14 in Channel 2), will ...

Page 2

Disabling/enabling Function The ISL85033 evaluation board contains S1, S2 switches to enable or disable each of the channels, thus allowing low quiescent current state. Table 1 details this function. TABLE 1. SWITCH SETTINGS S1 S2 ON/OFF CONTROL ON OFF Enable ...

Page 3

... ISL85033DUALEVAL1Z Schematic VOUT1 C1 C13 JVO1 R3 68PF 42.2K 12PF COMP1 69.8K FB1 470PF 2 FB1 SS1 3 SS1 SS1 PGND1 8.06K OPEN BOOT1 5 BOOT1 C5 6 GND1 PHASE1 A A 0.01UF 7 PHASE1 29 A JLX1 A VO1 L1 A VOUT1 7UH VOUT1=5V D1 C14 C2 B340B DNP 47UF VIN1 VIN1 C18 ...

Page 4

PART NUMBER QTY UNITS ISL85033EVAL1ZREVBPCB 1 ea EEE-FK1V101P GMK325BJ106KN H1044-00120-50V5 H1044-00680-50V5 H1045-00103-50V10 H1045-00471-50V5 H1045-00475-6R3V10 H1045-DNP 0 ea H1082-00106-50V10 H1082-00476-16V20 SQL004 2 ea ...

Page 5

... TF, ROHS R4, R6 RES, SMD, 0603, 1M, 1/10W, 1%, TF, ROHS MANUFACTURER MANUFACTURER PART # KEYSTONE 1514-2 KEYSTONE 5002 KEYSTONE 5002 DIODES INC. B340B-13-F INTERSIL ISL85033IRTZ VENKEL CR0402-16W-00T PANASONIC ERJ-2GE0JR00 VENKEL CR0402-16W-2552FT PANASONIC ERJ-2RKF2552X VISHAY/DALE CRCW040225K5FKED STACKPOLE RMC 1/16S 25. PANASONIC ERJ-2RKF4222X VENKEL CR0402-16W-4222FT ...

Page 6

... Bottom four corners BUMPONS, 0.44’ 0.20’ H, DOMETOP, BLACK Place assy in bag BAG, STATIC, 5X8, ZIPLOC, ROHS D3-D6 DO NOT POPULATE OR PURCHASE RENAME PCB TO: LABEL, TO RENAME ISL85033DUALEVAL1Z BOARD LABEL, FOR SERIAL NUMBER AND BOM REV # MANUFACTURER MANUFACTURER PART # VENKEL CR0603-10W-6982FT YAGEO RC0603FR-0769K8L ...

Page 7

... ISL85033DUALEVAL1Z Board Layout 7 Application Note 1574 FIGURE 1. TOP LAYER COMPONENTS FIGURE 2. TOP LAYER ETCH AN1574.2 November 29, 2010 ...

Page 8

... ISL85033DUALEVAL1Z Board Layout 8 Application Note 1574 (Continued) FIGURE 3. SECOND LAYER ETCH FIGURE 4. THIRD LAYER ETCH AN1574.2 November 29, 2010 ...

Page 9

... ISL85033DUALEVAL1Z Board Layout Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that the Application Note or Technical Brief is current before proceeding. For information regarding Intersil Corporation and its products, see www.intersil.com ...

Related keywords