DS92LV1212AMSA National Semiconductor, DS92LV1212AMSA Datasheet - Page 6

• Manufacturer Part Number: DS92LV1212AMSA
• Description: IC, DESERIALIZER, 40MHZ, 10BIT, SSOP-28
• Manufacturer: National Semiconductor

Specifications of DS92LV1212AMSA

• Serdes Function: Deserializer
• Data Rate: 400Mbps
• Ic Output Type: LVTTL
• No. Of Inputs: 1
• No. Of Outputs: 10
• Supply Voltage Range: 3V To 3.6V
• Driver Case Style: SSOP
• No. Of Pins: 28
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

www.national.com
Symbol
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
RCP
CLH
CHL
DD
ROS
ROH
RDC
HZR
LZR
ZHR
ZLR
DSR1
DSR2
ZHLK
RNM
Over recommended operating supply and temperature ranges unless otherwise specified.
Deserializer Switching Characteristics
Note 1: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices
should be operated at these limits. The table of “Electrical Characteristics” specifies conditions of device operation.
Note 2: Typical values are given for V
Note 3: Current into device pins is defined as positive. Current out of device pins is defined as negative. Voltages are referenced to ground except VOD, VOD, VTH
and VTL which are differential voltages.
Note 4: For the purpose of specifying Deserializer PLL performance tDSR1 and tDSR2 are specified with the REFCLK running and stable, and specific conditions
of the incoming data stream (SYNCPATs). It is recommended that the Deserializer be initialized using either tDSR1 timing or tDSR2 timing. tDSR1 is the time required
for the Deserializer to indicate lock upon power-up or when leaving the power-down mode. Synchronization patterns should be sent to the device before initiating
either condition. tDSR2 is the time required to indicate lock for the powered-up and enabled Deserializer when the input (RI+ and RI-) conditions change from not
receiving data to receiving synchronization patterns (SYNCPATs).
Note 5: tRNM is a measure of how much phase noise (jitter) the Deserializer can tolerate in the incoming data stream before bit errors occur.
Receiver out Clock
Period
CMOS/TTL Low-to-High
Transition Time
CMOS/TTL High-to-Low
Transition Time
Deserializer Delay
ROUT (0-9) Setup Data to
RCLK
ROUT (0-9) Hold Data to
RCLK
RCLK Duty Cycle
HIGH to TRI-STATE Delay
LOW to TRI-STATE Delay
TRI-STATE to HIGH Delay
TRI-STATE to LOW Delay
Deserializer PLL Lock Time
from PWRDWN (with
SYNCPAT)
Deserializer PLL Lock time
from SYNCPAT
TRI-STATE to HIGH Delay
(Power-up)
Deserializer Noise Margin
Parameter
CC
= 3.3V and T
Figure 3
t
CL = 15 pF
Figure 2
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
(Note 4)
Figure 9
(Note 5)
Conditions
RCP
= t
A
= +25˚C.
TCP
All Temp./All Freq. 1.75*t
LOCK, RCLK
Room Temp
3.3V/40MHz
Rout(0-9),
Rout(0-9),
Pin/Freq.
16 MHz
40 MHz
16MHz
40MHz
16MHz
40MHz
RCLK
RCLK
LOCK
LOCK
6
1.75*t
−0.4*t
0.4*t
RCP
RCP
Min
900
450
25
45
RCP
RCP
+ 1.25 1.75*t
+ 2.25 1.75*t
4.2+0.5*t
4.5+0.5*t
6.0+0.5*t
6+0.5*t
−0.5*t
0.5*t
1100
1.31
0.47
4.62
Typ
RCP
RCP
730
1.2
1.1
1.2
50
4
RCP
RCP
RCP
+3.75 1.75*t
+3.75 1.75*t
RCP
RCP
RCP
10+t
10+t
12+t
12+t
Max
62.5
RCP
RCP
55
10
12
4
4
3
5
1
RCP
RCP
RCP
RCP
+6.25
+5.25
Units
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
µs
µs
µs
µs
ns
ps
ps
%