PIC18LF8680-I/PT Microchip Technology, PIC18LF8680-I/PT Datasheet - Page 344

• Manufacturer Part Number: PIC18LF8680-I/PT
• Description: IC, 8BIT MCU, PIC18LF, 40MHZ, PLCC-64
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18LF8680-I/PT

• Controller Family/series: PIC18
• No. Of I/o's: 39
• Eeprom Memory Size: 1024Byte
• Ram Memory Size: 3328Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Core Size: 8 Bit
• Program Memory Size: 32768 Words
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: CAN, EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 68
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.25K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TFQFP
• Rohs Compliant: Yes
• Processor Series: PIC18LF
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3328 B
• Interface Type: I2C, SPI, AUSART, CAN
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 69
• Number Of Timers: 8
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM183032
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC18F6585/8585/6680/8680
FIGURE 23-7:
23.15 CAN Interrupts
The module has several sources of interrupts. Each of
these interrupts can be individually enabled or dis-
abled. The PIR3 register contains interrupt flags. The
PIE3 register contains the enables for the 8 main inter-
rupts. A special set of read-only bits in the CANSTAT
register, the ICODE bits, can be used in combination
with a jump table for efficient handling of interrupts.
All interrupts have one source with the exception of the
error interrupt and buffer interrupts in Mode 1 and 2. Any
of the error interrupt sources can set the error interrupt
flag. The source of the error interrupt can be determined
by
COMSTAT. In Mode 1 and 2, there are two interrupt
enable/disable and flag bits – one for all transmit buffers
and the other for all receive buffers.
The interrupts can be broken up into two categories:
receive and transmit interrupts.
The receive related interrupts are:
• Receive Interrupts
• Wake-up Interrupt
• Receiver Overrun Interrupt
• Receiver Warning Interrupt
• Receiver Error-Passive Interrupt
DS30491C-page 342
reading
the
Communication
ERROR MODES STATE DIAGRAM
RXERRCNT < 127 or
TXERRCNT < 127
Passive
Error
Status
-
register,
TXERRCNT > 255
RXERRCNT > 127 or
TXERRCNT > 127
Active
Error
priority interrupt that is pending (if any) will be reflected
The transmit related interrupts are:
• Transmit Interrupts
• Transmitter Warning Interrupt
• Transmitter Error-Passive Interrupt
• Bus-Off Interrupt
23.15.1
To simplify the interrupt handling process in user firm-
ware, the ECAN module encodes a special set of bits. In
Mode 0, these bits are ICODE<2:0> in the CANSTAT
register. In Mode 1 and 2, these bits are EICODE<3:0>
in the CANSTAT register. Interrupts are internally priori-
tized such that the higher priority interrupts are assigned
lower values. Once the highest priority interrupt condi-
tion has been cleared, the code for the next highest
by the ICODE bits. Note that only those interrupt sources
that have their associated interrupt enable bit set will be
reflected in the ICODE bits.
In Mode 2, when a receive message interrupt occurs,
EICODE bits will always consist of ‘10000’. User
firmware may use FIFO pointer bits to actually access
the next available buffer.
-
Bus
Off
-
INTERRUPT CODE BITS
Reset
128 occurrences of
11 consecutive
“recessive” bits
 2004 Microchip Technology Inc.