PIC16F1826-I/MQ Microchip Technology, PIC16F1826-I/MQ Datasheet - Page 52

• Manufacturer Part Number: PIC16F1826-I/MQ
• Description: IC, 8BIT MCU, PIC16F, 32MHZ, QFN-28
• Manufacturer: Microchip Technology

Specifications of PIC16F1826-I/MQ

• Controller Family/series: PIC16F
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 256Byte
• Cpu Speed: 32MHz
• No. Of Timers: 3
• Interface: EUSART, I2C, SPI
• Core Size: 8 Bit
• Program Memory Size: 2kWords
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC16F/LF1826/27
REGISTER 4-2:
DS41391B-page 52
bit 13
bit 6
Legend:
R = Readable bit
u = Bit is unchanged
‘1’ = Bit is set
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8
bit 7-5
bit 4
bit 3-2
bit 1-0
Note 1:
R/P-1/1
LVP
U-1
—
The LVP bit cannot be programmed to ‘0’ when Programming mode is entered via LVP.
LVP: Low-Voltage Programming Enable bit
1 = Low-voltage programming enabled
0 = High-voltage on MCLR must be used for programming
DEBUG: In-Circuit Debugger Mode bit
1 = In-Circuit Debugger disabled, ICSPCLK and ICSPDAT are general purpose I/O pins
0 = In-Circuit Debugger enabled, ICSPCLK and ICSPDAT are dedicated to the debugger
Unimplemented: Read as ‘1’
BORV: Brown-out Reset Voltage Selection bit
1 = Brown-out Reset voltage set to 1.9V (typical)
0 = Brown-out Reset voltage set to 2.5V (typical)
STVREN: Stack Overflow/Underflow Reset Enable bit
1 = Stack Overflow or Underflow will cause a Reset
0 = Stack Overflow or Underflow will not cause a Reset
PLLEN: PLL Enable bit
1 = 4xPLL enabled
0 = 4xPLL disabled
Unimplemented: Read as ‘1’
Reserved: This location should be programmed to a ‘1’.
Unimplemented: Read as ‘1’
WRT<1:0>: Flash Memory Self-Write Protection bits
2 kW Flash memory (PIC16F/LF1826 only):
4 kW Flash memory (PIC16F/LF1827 only):
DEBUG
R/P-1/1
11 = Write protection off
10 = 000h to 1FFh write-protected, 200h to 7FFh may be modified by EECON control
01 = 000h to 3FFh write-protected, 400h to 7FFh may be modified by EECON control
00 = 000h to 7FFh write-protected, no addresses may be modified by EECON control
11 = Write protection off
10 = 000h to 1FFh write-protected, 200h to FFFh may be modified by EECON control
01 = 000h to 7FFh write-protected, 800h to FFFh may be modified by EECON control
00 = 000h to FFFh write-protected, no addresses may be modified by EECON control
CONFIGURATION WORD 2
U-1
—
W = Writable bit
‘0’ = Bit is cleared
x = Bit is unknown
Reserved
R/P-1/1
U-1
—
Preliminary
R/P-1/1
(1)
BORV
U-1
—
U = Unimplemented bit, read as ‘0’
-n/n = Value at POR and BOR/Value at all other Resets
STVREN
R/P-1/1
U-1
—
© 2009 Microchip Technology Inc.
R/P-1/1
R/P-1/1
PLLEN
WRT1
R/P-1/1
WRT0
U-1
—
bit 7
bit 0