E158AC ETERNA, E158AC Datasheet

E158AC

Manufacturer Part Number

E158AC

Description

FLUORESCENT FITTING, IP65, 1X1500MM

Manufacturer

ETERNA

Datasheet

1.E158AC.pdf (2 pages)

Specifications of E158AC

Supply Voltage

240V

Base Type

T8 Fluorescent 1500mm

Power Rating

58W

Length

1575mm

Svhc

No SVHC (15-Dec-2010)

External Width

90mm

Height

90mm

Ip/nema Rating

IP65

Lamp Base Type

T8 Fluorescent 1500mm

Rohs Compliant

Yes

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

Current page: 1 of 2
Download datasheet (360Kb)

Cleaning

Clean this light ﬁtting only with a soft dry cloth

Disconnect the power and clean the exterior

only of this ﬁtting with a moist (not wet) cloth.

The diffuser may be removed and washed

in a mild detergent solution. Make sure it is

completely dry before putting back on your

ﬁtting.

Do not use any chemical or abrasive cleaners.

If you experience problems...

If your light is defective or develops a fault, please return it to the place where you bought it. You can

call our Helpline for advice. The Helpline will gladly give advice on any aspect of any Eterna Lighting

product but may not be able to give speciﬁc instructions regarding individual installations.

If in doubt, consult a qualiﬁed electrician.

Help Line

Tel:

Fax:

Email: sales@eterna-lighting.co.uk

For all other information visit our website www.eterna-lighting.co.uk

Eventually, you may want to replace this light ﬁtting

When your light ﬁtting comes to the end of its life or you choose to update or upgrade it by

replacing it, please do not dispose of it with your normal household waste, please recycle where

facilities exist. When you need to dispose of this ﬁtting, check with your retailer or local authority

for suitable options. New regulations require the recycling of Waste from Electrical and Electronic

Equipment (European “WEEE Directive” effective August 2005—UK WEEE Regulations effective 2nd

January 2007). Environment Agency Registered Producer: WEE/GA0248QZ

01933 673 144

01933 678 083

Piece

Locating point

Fig. 3

Lamp replacement

1. Switch off the electricity at the mains.

2. Loosen the clips around the ﬁtting and

3. Twist the ﬂuorescent tube through 90° and

4. Slide the new tube into the slots and turn

5. Re-ﬁt the diffuser ensuring that it is correctly

6. Restore the power and switch on.

Replacement lamp type:

Wattage:

Supply Voltage:

Size / type:

remove the diffuser.

pull it out of the slots in the lampholders.

through approximately 90° until it clicks into

place making sure it is of the same type and

wattage as stated below and on the lamp

detail label.

seated in the soft foam gasket and that all of

the clips are properly snapped home.

58 W

240 V

T8 ﬂuorescent

IMPORTANT! Please read these instructions before installing your new ﬁtting.

SAFETY AND INSTALLATION

Models: E158AC, E258AC

Pack Contents

Damp-proof ﬂuorescent batten x 1

Fixing pack

Diffuser clips

Hanging clips

Please retain for future reference.

INSTRUCTIONS

x 1

x 10

x 2

Related parts for E158AC

E158AC Summary of contents

Page 1

... For all other information visit our website www.eterna-lighting.co.uk IMPORTANT! Please read these instructions before installing your new ﬁtting 240 V T8 ﬂuorescent SAFETY AND INSTALLATION INSTRUCTIONS Models: E158AC, E258AC Please retain for future reference. Pack Contents Damp-proof ﬂuorescent batten x 1 Fixing pack x 1 Diffuser clips ...

Page 2

... Live - Brown or Red which you have intended it. Eterna Lighting Neutral - Blue or Black cannot accept any liability for loss, damage or Earth - Green and Yellow premature failure resulting from inappropriate When making connections, ensure that the use ...

Related keywords

E158AC datasheet
E158AC data sheet
E158AC pdf datasheet
E158AC component
E158AC part
E158AC distributor
E158AC RoHS
E158AC datasheet download