E158AC ETERNA, E158AC Datasheet - Page 2

• Manufacturer Part Number: E158AC
• Description: FLUORESCENT FITTING, IP65, 1X1500MM
• Manufacturer: ETERNA

Specifications of E158AC

• Supply Voltage: 240V
• Base Type: T8 Fluorescent 1500mm
• Power Rating: 58W
• Length: 1575mm
• Svhc: No SVHC (15-Dec-2010)
• External Width: 90mm
• Height: 90mm
• Ip/nema Rating: IP65
• Lamp Base Type: T8 Fluorescent 1500mm
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Read this first
Check the pack and make sure you have all of
the parts listed on the front of this booklet. If
not, contact the outlet where you bought this
product.
This fully assembled fitting contains glass, care
must be taken when assembling, fitting or
handling to prevent personal injury or damage
to the product.
This light fitting must be installed by a
competent person in accordance with the
Building Regulations making reference to the
current edition of the IEE Wiring Regulations
(BS7671). The Building Regulations may
be obtained from HMSO or viewed and
downloaded from www.communities.gov.uk
following the link for Building Regulations.
As the buyer, installer and/or user of this
product it is your own responsibility to ensure
that this fitting is fit for the purpose for
which you have intended it. Eterna Lighting
cannot accept any liability for loss, damage or
premature failure resulting from inappropriate
use.
If in any doubt, consult a qualified electrician.
Switch off the mains before commencing
installation and remove the appropriate circuit
fuse.
When working at heights, please use a suitable
platform.
Suitable for indoor and outdoor use.
This product is suitable for installation on
surfaces with normal flammability (indicated by
the “F” in a triangle) e.g. wood, plasterboard,
masonry. It is not suitable for use on highly
flammable surfaces (e.g. polystyrene, textiles).
Before making fixing hole(s), check that there
are no obstructions hidden beneath the
mounting surface such as pipes or cables.
The chosen location of your new fitting should
allow for the product to be securely mounted
(e.g. to a ceiling joist) and safely connected to
the mains supply (lighting circuit).
Do not attach to surfaces which are damp,
freshly painted or otherwise electrically
conductive (e.g. metallic surfaces).
If the location of your new fitting requires the
provision of a new electrical supply, the supply
must conform with the requirements of the
Building Regulations making reference to the
current edition of the IEE Wiring Regulations
(BS7671).
This product is designed for permanent
connection to fixed wiring: this should be either
a suitable lighting circuit (protected with a 5
or 6 Amp MCB or fuse) or a fused spur (with
a 3 Amp fuse) via a fused connection unit. We
recommend that the supply incorporates a
switch for ease of operation.
Make connections to the electrical supply in
accordance with the
following code:
Live - Brown or Red
Neutral - Blue or Black
Earth - Green and Yellow
When making connections, ensure that the
terminals are tightened securely and that
no strands of wire protrude. Check that
the terminals are tightened onto the bared
conductors and not onto any insulation. Wrap
loose terminal blocks well with insulating tape.
This product must be connected to Earth.
IMPORTANT: Always switch off at the mains
before changing the lamp.
You are advised at every stage of your
installation to double-check any electrical
connections you have made. After you have
completed your installation there are electrical
tests that should be carried out: these tests are
specified in the Wiring Regulations (BS7671)
referred to in the Building Regulations. If in
doubt, consult a qualified electrician.
Safety Markings
IP65
Installation
1. Choose the location of your new fitting giving
2. Push down and outwards on the top, flat part
3. Press together the tops of the clips protruding
4. If fixing direct to a mounting surface, clear
5. Using the back of the fitting as a template,
6. If fixing directly to a solid surface, drill holes
7. Secure your fitting in position using the
Ensure clips
latch correctly
screws and washers supplied. Put the
washer onto the screw before fixing. If the
fixings supplied are not appropriate to your
installation, please select suitable alternatives.
consideration to all of the conditions listed
above and the position of the entry points for
the mains supply cable.
of the diffuser clips to open up the fitting.
through the middle of the gear tray and lift
the gear tray out of the fitting, see Fig.1.
through the four mounting holes on the back
of the fitting, visible from the outside, using a
5mm drill.
mark the location of the fixing holes on your
mounting surface.
using a N°8 / 5mm drill bit and insert the
plastic plugs supplied.
Fig. 1
Fig. 2
8. Hanging clips are supplied (Fig. 2) to allow
9. Ensure that the chain is strong enough to
10. Pierce the centre of the soft gland at the
11. Thread the supply cable through the gland.
12. On the white metal gear tray, locate the
13. Make connections to the terminal block
14. Locate the gear tray over the plastic clips
15. Fit the fluorescent tube(s) (not supplied)
16. Hold the diffuser in position on the fitting so
17. Position the bottom of each hook in the lip
18. Restore the power supply and switch on.
Take care not to over tighten fixing screws to
prevent damaging the case.
you to suspend the fitting from chains (not
supplied).
support the weight of the fitting and that the
tops of the chains are fixed securely to the
mounting surface.
of the diffuser and press the thumb catches
up and over to lock firmly in position. (See
over Fig. 3)
end of the fitting adjacent to the supply
wiring. Take care not to make the hole too
large as the tight fit of the gland to the cable
is essential for it to remain waterproof.
Alternatively, fit a gland/nut assembly.
lampholders in the rectangular slots at each
end of the fitting. The lampholders must
be positioned so that the slots on each
lampholder face the centre of the fitting.
Also, the small pin on the front of the
lampholder must locate in the small hole
next to the rectangular slot.
on the back of the white metal gear tray
according to the colour code opposite.
protruding from the case and press the gear
tray into position. Ensure that all clips have
latched securely.
by pushing the pins into the slots in the
lampholders and turning the tube through
90° or until it clicks into position.
that it is seated on the soft foam gasket all
the way around.