SFPCA455KF4A-R1 Murata, SFPCA455KF4A-R1 Datasheet - Page 15

• Manufacturer Part Number: SFPCA455KF4A-R1
• Description: Signal Conditioning 455kHz CERAFIL for AM
• Manufacturer: Murata
• Type: Ceramic Filterr

Specifications of SFPCA455KF4A-R1

• Rad Hardened: No
• Product: Ceramic Filters
• Frequency: 455 KHz
• Frequency Range: 455 KHz +/- 1.5 KHz
• Impedance: 1.5 KOhms
• Operating Temperature Range: - 20 C to + 80 C
• Lead Free Status / RoHS Status: Compliant

!Note
!Note
1. Standard Reflow Soldering Condition
(1) Reflow
(2) Soldering Iron
2. Wash
1. Standard Reflow Soldering Condition
(1) Reflow
(2) Soldering Iron
2. Wash
(1) Cleaning Solvent
(2) Cleaning Conditions
(3) Notice
CFXC_ Series Notice (Soldering and Mounting)
SFPCA/CFUCG/CFUCF Series Notice (Soldering and Mounting)
Filter is soldered twice within the following temperature
condition and then being placed in natural condition for
24 hours.
Elecrode is directly contacted with the tip of soldering iron
of +350 5 C for 3 1 seconds, and then being placed in
natural condition for 24 hours.
The component cannot be withstand washing.
Filter is soldered one time within the following
temperature condition and then being placed in natural
condition for 24 hours.
Electrode is directly with the tip of soldering iron of +350
condition for 24hours.
CFC alternatives(HCFC Series), Isopropyl Alcohol(IPA),
Water(Demineralized Water), Cleaning Water
Solution(Cleanthrough-750H, Pine Alha 100S),
Silicon(Technocare FRW)
5 C for 3 1 seconds, and then being placed in natural
• Please read rating and !CAUTION (for storage and operating, rating, soldering and mounting, handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specification or transact the approval sheet for product specification before ordering.
Immersion Wash
2 minutes max. in above solvent at +60 C max.
Shower or Rinse Wash
2 minutes max. in above solvent at +60 C max.
When components are immersed in solvent, be sure to
maintain the temperature of components below the
temperature of solvent.
Please do not use ultrasonic cleaning.
Total washing time should be within 4minutes.
Please ensure the component is thoroughly evaluated
in your application circuit.
Please do not use chlorine, petroleum and alkali
cleaning solvent.
If you plan to use any other type of solvents, please
consult with Murata or MUrata representative prior to
using.
Please read rating and !CAUTION (for storage and operating, rating, soldering and mounting, handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specification or to transact the approval sheet for product specificaion before ordering.
kHz SMD Type CERAFILr Notice
240
200
100
240
200
100
30sec. min. 60sec.-120sec.
30sec. min. 60sec.-120sec.
(140-160 C)
(140-160 C)
Pre-heating
Pre-heating
Continued on the following page.
(240 C max.)
(235 C max.)
50sec. max. 120sec. min.
50sec. max. 120sec. min.
(200 C)
(200 C)
Heating
Heating
Peak
Peak
P05E11.pdf 02.9.2
Gradual
Cooling
Gradual
Cooling
19
7