CS5534-BSZR Cirrus Logic Inc, CS5534-BSZR Datasheet - Page 14

• Manufacturer Part Number: CS5534-BSZR
• Description: IC,Data Acquisition Signal Conditioner,4-CHANNEL,24-BIT,CMOS,SSOP,24PIN,PLASTIC
• Manufacturer: Cirrus Logic Inc

Specifications of CS5534-BSZR

• Number Of Bits: 24
• Sampling Rate (per Second): 3.84k
• Data Interface: Serial
• Number Of Converters: 1
• Power Dissipation (max): 45mW
• Voltage Supply Source: Analog and Digital, Dual ±
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-SSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 598-1016 - EVAL BOARD FOR CS5534
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

2.1.4. No Offset DAC
An offset DAC was not included in the CS553X
family because the high dynamic range of the con-
verter eliminates the need for one. The offset regis-
ter can be manipulated by the user to mimic the
function of a DAC if desired.
2.2. Overview of ADC Register Structure
and Operating Modes
The CS5532/34 ADCs have an on-chip controller,
which includes a number of user-accessible regis-
ters. The registers are used to hold offset and gain
calibration results, configure the chip's operating
modes, hold conversion instructions, and to store
conversion data words. Figure 6 depicts a block di-
agram of the on-chip controller’s internal registers.
Each of the converters has 32-bit registers to func-
tion as offset and gain calibration registers for each
channel. The CS5532 has two offset and two gain
calibration registers, the CS5534 has four offset
and four gain calibration registers. These registers
14
Offset Registers (4 x 32)
Power Save Select
Reset System
Input Short
Guard Signal
Voltage Reference Select
Output Latch
Output Latch Select
Offset/Gain Select
Filter Rate Select
Offset 2 (1 x 32)
Offset 3 (1 x 32)
Offset 4 (1 x 32)
Offset 1 (1 x 32)
Configuration Register (1 x 32)
Figure 6. CS5532/34 Register Diagram
Gain Registers (4 x 32)
Gain 1 (1 x 32)
Gain 2 (1 x 32)
Gain 3 (1 x 32)
Gain 4 (1 x 32)
Channel Select
Gain
W ord Rate
Unipolar/Bipolar
Output Latch
Delay Time
Open Circuit Detect
Offset/Gain Pointer
hold calibration results. The contents of these reg-
isters can be read or written by the user. This allows
calibration data to be off-loaded into an external
EEPROM. The user can also manipulate the con-
tents of these registers to modify the offset or the
gain slope of the converter.
The converters include a 32-bit configuration reg-
ister which is used for setting options such as the
power down modes, resetting the converter, short-
ing the analog inputs, and enabling diagnostic test
bits like the guard signal.
A group of registers, called Channel Setup Regis-
ters, are used to hold pre-loaded conversion in-
structions. Each channel setup register is 32 bits
wide, and holds two 16-bit conversion instructions
referred to as Setups. Upon power up, these regis-
ters can be initialized by the system microcontrol-
ler with conversion instructions. The user can then
instruct the converter to perform single or multiple
Setup 1
(1 x 16)
Setup 3
(1 x 16)
Setup 5
(1 x 16)
Setup 7
(1 x 16)
Registers (4 x 32)
Channel Setup
Setup 2
(1 x 16)
Setup 4
(1 x 16)
Setup 6
(1 x 16)
Setup 8
(1 x 16)
Register (1 × 8)
Com mand
Conversion Data
Register (1 x 32)
Data (1 x 32)
Interface
CS5532/34-BS
Serial
CS
SDI
SDO
SCLK
DS755F3