8200801LA E2V, 8200801LA Datasheet - Page 11

• Manufacturer Part Number: 8200801LA
• Manufacturer: E2V

Specifications of 8200801LA

• Lead Free Status / RoHS Status: Supplier Unconfirmed

DSCC FORM 2234
APR 97
as specified in table I and shall apply over the full case operating temperature range.
tests for each subgroup are described in table I.
in 1.2 herein. In addition, the manufacturer's PIN may also be marked.
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and
Maritime-VA prior to listing as an approved source of supply shall affirm that the manufacturer's product meets the
requirements of MIL-PRF-38535, appendix A and the requirements herein.
with each lot of microcircuits delivered to this drawing.
this drawing.
option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made
available onshore at the option of the reviewer.
in a wide variety of configurations; two processing options are provided for selection in the contract, using an altered item
drawing.
and table II. It is recommended that users perform subgroups 7 and 9 after programming to verify the specific program
configuration.
herein, including the requirements of the altered item drawing, shall be satisfied by the manufacturer prior to delivery.
prior to quality conformance inspection. The following additional criteria shall apply:
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
3.8 Notification of change. Notification of change to DLA Land and Maritime-VA shall be required for any change that affects
3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritime's agent, and the acquiring activity retain the
3.10. Processing options. Since the device is capable of being programmed by either the manufacturer or the user to result
3.10.1 Unprogrammed device delivered to the user. All testing shall be verified through group A testing as defined in 3.2.3.1
3.10.2 Manufacturer-programmed device delivered to the user. All testing requirements and quality assurance provisions
4. VERIFICATION
appendix A.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535,
4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices
a.
b.
c.
Burn-in test, method 1015 of MIL-STD-883.
(1)
(2)
Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
All devices processed to an altered item drawing may be programmed either before or after burn-in at the
manufacturer's discretion. The required electrical testing shall include, as a minimum, the final electrical tests for
programmed devices as specified in table II herein.
MICROCIRCUIT DRAWING
COLUMBUS, OHIO 43218-3990
Test condition A, C, D, or E. The test circuit shall be maintained by the manufacturer under document revision
level control and shall be made available to the preparing or acquiring activity upon request. The test circuit
shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent
specified in method 1015 of MIL-STD-883.
T
A
DLA LAND AND MARITIME
= +125C, minimum.
STANDARD
SIZE
A
REVISION LEVEL
L
SHEET
82008
11