ICS9248DF-39LF IDT, Integrated Device Technology Inc, ICS9248DF-39LF Datasheet - Page 11

• Manufacturer Part Number: ICS9248DF-39LF
• Description: IC GEN/BUFFER PENTIUM PRO 48SSOP
• Manufacturer: IDT, Integrated Device Technology Inc
• Type: Frequency Generatorr

Specifications of ICS9248DF-39LF

• Input: Crystal
• Output: Clock
• Frequency - Max: 150MHz
• Voltage - Supply: 3.135 V ~ 3.465 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 48-SSOP
• Frequency-max: 150MHz
• Number Of Elements: 2
• Supply Current: 180mA
• Pll Input Freq (min): 12MHz
• Pll Input Freq (max): 16MHz
• Operating Supply Voltage (typ): 3.3V
• Operating Temp Range: 0C to 70C
• Package Type: SSOP
• Output Frequency Range: 24 to 150MHz
• Operating Supply Voltage (min): 3.135V
• Operating Supply Voltage (max): 3.465V
• Operating Temperature Classification: Commercial
• Pin Count: 48
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 9248DF-39LF

0277G—08/04/04
How to Write:
• Controller (host) sends a start bit.
• Controller (host) sends the write address D2
• ICS clock will acknowledge
• Controller (host) sends a dummy command code
• ICS clock will acknowledge
• Controller (host) sends a dummy byte count
• ICS clock will acknowledge
• Controller (host) starts sending first byte (Byte 0)
• ICS clock will acknowledge each byte one at a time.
• Controller (host) sends a Stop bit
Notes:
1.
2.
3.
4.
5.
6.
through byte 5
The ICS clock generator is a slave/receiver, I
verification. Read-Back will support Intel PIIX4 "Block-Read" protocol.
The data transfer rate supported by this clock generator is 100K bits/sec or less (standard mode)
The input is operating at 3.3V logic levels.
The data byte format is 8 bit bytes.
To simplify the clock generator I
The bytes must be accessed in sequential order from lowest to highest byte with the ability to stop after any
complete byte has been transferred. The Command code and Byte count shown above must be sent, but the
data is ignored for those two bytes. The data is loaded until a Stop sequence is issued.
At power-on, all registers are set to a default condition, as shown.
Dummy Command Code
Dummy Byte Count
Controller (Host)
Address
Start Bit
Stop Bit
Byte 0
Byte 1
Byte 2
Byte 3
Byte 4
Byte 5
D2
(H)
For more information, contact ICS for an I
The information in this section assumes familiarity with I
How to Write:
General I
ICS (Slave/Receiver)
ACK
ACK
ACK
ACK
ACK
ACK
ACK
ACK
ACK
2
C interface, the protocol is set to use only "Block-Writes" from the controller.
2
C serial interface information
(H)
2
C component. It can read back the data stored in the latches for
11
2
C programming application note.
How to Read:
• Controller (host) will send start bit.
• Controller (host) sends the read address D3
• ICS clock will acknowledge
• ICS clock will send the byte count
• Controller (host) acknowledges
• ICS clock sends first byte (Byte 0) through byte 5
• Controller (host) will need to acknowledge each byte
• Controller (host) will send a stop bit
Controller (Host)
Address
Start Bit
Stop Bit
D3
ACK
ACK
ACK
ACK
ACK
ACK
ACK
2
C programming.
(H)
How to Read:
ICS (Slave/Receiver)
ICS9248-39
Byte Count
Byte 0
Byte 1
Byte 2
Byte 3
Byte 4
Byte 5
ACK
(H)