MAX5304CUA+ Maxim Integrated Products, MAX5304CUA+ Datasheet - Page 7

IC DAC 10BIT LP VOLT OUT 8-UMAX

MAX5304CUA+

Manufacturer Part Number
MAX5304CUA+
Description
IC DAC 10BIT LP VOLT OUT 8-UMAX
Manufacturer
Maxim Integrated Products
Datasheet

Specifications of MAX5304CUA+

Settling Time
10µs
Number Of Bits
10
Data Interface
Serial
Number Of Converters
1
Voltage Supply Source
Single Supply
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Number Of Dac Outputs
1
Resolution
10 bit
Interface Type
Serial (SPI)
Supply Voltage (max)
5.5 V
Supply Voltage (min)
4.5 V
Maximum Operating Temperature
+ 70 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
0 C
Supply Current
400 uA
Voltage Reference
External
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power Dissipation (max)
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
In shutdown mode, the amplifier’s output and the refer-
ence input enter a high-impedance state. The serial
interface remains active. Data in the input register is
retained in shutdown, allowing the MAX5304 to recall
the output state prior to entering shutdown. Exit shut-
down mode by either recalling the previous configura-
tion or updating the DAC with new data. When
powering up the device or bringing it out of shutdown,
allow 20µs for the outputs to stabilize.
The MAX5304’s 3-wire serial interface is compatible
with MICROWIRE (Figure 2) and SPI/QSPI (Figure 3).
The serial-input word consists of three control bits fol-
lowed by 10+3 data bits (MSB first), as shown in Figure
4. The 3-bit control code determines the MAX5304’s
response outlined in Table 1.
The MAX5304’s digital inputs are double buffered.
Depending on the command issued through the serial
interface, the input register can be loaded without
affecting the DAC register, the DAC register can be
loaded directly, or the DAC register can be updated
from the input register (Table 1).
The MAX5304 requires 16 bits of serial data. Table 1
lists the serial-interface programming commands. For
certain commands, the 10+3 data bits are “don’t
cares.” Data is sent MSB first and can be sent in two 8-
bit packets or one 16-bit word (CS must remain low
until 16 bits are transferred). The serial data is com-
posed of three control bits (C2, C1, C0), followed by
the 10+3 data bits D9...D0, S2, S1, S0 (Figure 4). Set
the sub-bits (S2, S1, S0) to zero. The 3-bit control code
determines the register to be updated and the configu-
ration when exiting shutdown.
Figure 5 shows the serial-interface timing requirements.
The chip-select pin (CS) must be low to enable the
DAC’s serial interface. When CS is high, the interface
control circuitry is disabled. CS must go low at least
t
erly clock in the first bit. When CS is low, data is
clocked into the internal shift register through the serial-
data input pin (DIN) on SCLK’s rising edge. The maxi-
mum guaranteed clock frequency is 10MHz. Data is
latched into the MAX5304 input/DAC register on CS’s
rising edge.
CSS
before the rising serial-clock (SCLK) edge to prop-
Serial-Interface Configurations
_______________________________________________________________________________________
Serial-Interface Description
10-Bit Voltage-Output DAC
Figure 2. Connections for MICROWIRE
Figure 4. Serial-Data Format
Figure 3. Connections for SPI/QSPI
MSB ..................................................................................LSB
C2
3 Control
MAX5304
Control
MAX5304
Bits
Bits
C1
C0
SCLK
SCLK
DIN
DIN
CS
16 Bits of Serial Data
CS
MSB............................LSB Sub-Bits
D9 ...............................D0, S2, S1, S0
in 8-Pin µMAX
10+3 Data Bits
CPOL = 0, CPHA = 0
Data Bits
MOSI
SCK
I/O
SK
SO
I/O
MICROWIRE
SPI/QSPI
PORT
PORT
+5V
SS
7

Related parts for MAX5304CUA+