CS4353-CZZ Cirrus Logic Inc, CS4353-CZZ Datasheet - Page 7

• Manufacturer Part Number: CS4353-CZZ
• Description: IC DAC STER 106DB 2VRMS 24-QFN
• Manufacturer: Cirrus Logic Inc

Specifications of CS4353-CZZ

• Number Of Bits: 24
• Data Interface: Serial
• Number Of Converters: 1
• Voltage Supply Source: Single Supply
• Power Dissipation (max): 152mW
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 598-1519 - BOARD EVAL FOR CS4353 DAC
• Settling Time: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

DS803F1
DAC ANALOG CHARACTERISTICS
Test conditions (unless otherwise specified): T
CPGND = 0 V; VBIAS, VFILT+/-, and FLYP/N+/- capacitors as shown in
997 Hz sine wave at 0 dBFS; measurement bandwidth 10 Hz to 20 kHz.
Notes: 2. Measured at the output of the external LPF on AOUTx as shown in
Dynamic Performance, Fs = 48, 96, and 192 kHz (Notes 2,
Dynamic Range
Total Harmonic Distortion + Noise
Idle Channel Noise / Signal-to-Noise Ratio
Interchannel Isolation
Analog Output
Full Scale AOUTx Output Voltage
Max Current Draw from an AOUTx Pin
Interchannel Gain Mismatch
Output Offset
Gain Drift
Output Impedance
AC-Load Resistance
Load Capacitance
AOUT_REF Rejection
Analog Reference Input
AOUT_REF Input Voltage
3. One-half LSB of triangular PDF dither is added to data.
4. Measured with the specified minimum AC-Load Resistance present on the AOUTx pins.
5. Measured between the AOUTx and AOUT_REF pins.
6. External impedance between the AOUTx pin and the load will lower the voltage delivered to the load.
7. V
8. Measured with AOUT_REF connected directly to ground. External impedance between AOUT_REF
Note that for sine wave signals:
and ground will lower the AOUT_REF rejection.
PP
(Note
is the controlling specification. V
Parameter
5)
24-bit
24-bit
16-bit
16-bit A-Weighted
(Notes 4, 6, 7)
A-Weighted
(Notes 8, 9)
unweighted
unweighted
(Note 10)
(1 kHz)
-20 dB
-60 dB
-20 dB
-60 dB
(A-wt)
0 dB
0 dB
V
RMS
A
= 25 °C; VCP = VA = 3.3 V; AOUT_REF = AGND = DGND =
Symbol
I
THD+N
RMS
OUTmax
Z
AOR
=
R
C
OUT
L
L
--------- -
2 2
V
specification valid for sine wave signals only.
pp
Min
1.02
2.89
94
91
5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1_2VRMS = 0
3,
4)
1.08
3.05
Typ
100
100
575
100
100
115
-93
-77
-37
-93
-75
-29
0.1
97
92
89
±5
40
-
-
-
Figure 3 on page
Max
1000
1.13
3.20
-87
-71
-31
0.2
±8
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Figure 3 on page
Min
2.04
5.78
100
97
5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1_2VRMS = 1
12; input test signal is a
Typ
2.15
6.09
106
103
106
115
575
100
100
-93
-83
-43
-93
-75
-35
0.1
98
95
±5
40
-
-
-
12.
Max
1000
2.26
6.40
-87
-77
-37
0.2
±8
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
CS4353
ppm/°C
V
Unit
Vpp
V
mV
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
μA
dB
kΩ
pF
dB
RMS
Ω
pp
7