PVZ2A501A01R00 Murata, PVZ2A501A01R00 Datasheet - Page 3

• Manufacturer Part Number: PVZ2A501A01R00
• Description: Trimmer Resistors - SMD 500 OHM SMD 2MM
• Manufacturer: Murata

Specifications of PVZ2A501A01R00

• Resistance: 500 Ohms
• Tolerance: 30 %
• Power Rating: 0.1 Watt (1/10 Watt)
• Operating Temperature Range: - 25 C to + 85 C
• Element Type: Carbon
• Number Of Turns: 1
• Product: Single-Turn Trimmer Potentiometers
• Taper: Linear
• Termination Style: SMD/SMT
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

!Note
!Note
1. Store that the temperature is -10 to +40deg. C and
2. Do not store in or near corrosive gases.
3. Use within six months after delivery.
4. Open the package just before using.
5. Do not store under direct sunlight.
6. The trimmer potentiometer should not be used under
1. When using with partial load (rheostat), minimize
2. The maximum input voltage to a trimmer
3. The maximum input current to a trimmer
1. Soldering
(1) Reflow soldering and Soldering Iron are
(2) Use our standard land dimension. Excessive land
(3) Standard soldering condition
(4) Apply the appropriate amount of solder paste.
Notice (Operating and Storage Conditions)
the relative humidity is 30-85%RH.
the following environmental conditions:
If you use the trimmer potentiometer in an
environment other these listed below, please
consult with Murata factory representative prior to
Notice (Rating)
the power depend on the resistance value.
potentiometer should not exceed (P•R)^1/2 or the
maximum operating voltage, whichever is smaller.
potentiometer should not exceed (P/R)^1/2 or the
allowable wiper current, whichever is smaller.
Notice (Soldering and Mounting)
(a) Reflow soldering :
(b) Soldering iron:
available. Can not be soldered using the flow
soldering method. If you use the flow soldering
method, the trimmer potentiometer may not
function.
area causes displacement due to effect of the
surface tension of the solder. Insufficient
land area leads to insufficient soldering
strength of the chip.
Before using other soldering conditions than
those listed above, please consult with Murata
factory representative prior to using. If the
soldering conditions are not suitable, e. g.,
excessive time and/or excessive temperature, the
trimmer potentiometer may deviate from the
specified characteristics.
The thickness of solder paste should be printed
from 100micro m to 150micro m and the dimension
• Please read rating and !CAUTION (for storage and operating, rating, soldering and mounting, handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specification or transact the approval sheet for product specification before ordering.
Please read rating and !CAUTION (for storage and operating, rating, soldering and mounting, handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specification or to transact the approval sheet for product specificaion before ordering.
>Temperature of tip 260deg. C max.
>Soldering time
>Diameter
Refer to the standard temperature profile.
1mm max.
3sec. max.
2. Mounting
3. Cleaning
(1) Corrosive gaseous atmosphere.
(2) In liquid.
(3) Dusty/dirty atmosphere.
(4) Direct sunlight.
(5) Static voltage nor electric/magnetic fields.
(6) Direct sea breeze.
(7) Other variations of the above.
(5) The soldering iron should not come in contact
(1) Do not apply excessive force (preferable 4.9N
(2) Do not warp and/or bend PC board to prevent
(3) In chip placers, the recommended size of the
(1) In case there is flux on the resistive element,
(2) Isopropyl-alcohol and Ethyl-alcohol are
using.
(Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia
gas, Sulfuric acid gas, Nitric oxie gas, etc.)
(Ex. Oil, Medical liquid, Organic solvent, etc.)
of land pattern should be used Murata's
standard land pattern at reflow soldering.
Insufficient amounts of solder can lead to
insufficient soldering strength on PCB.
Excessive amounts of solder may cause the
bridging between the terminals.
with the case of the trimmer potentiometer. If
such contact does occur, the trimmer
potentiometer may be damaged.
(Ref.; 500gf) max.), when the trimmer
potentiometer is mounted to the PCB.
trimmer potentiometer from breakage.
cylindrical pick-up nozzle should be outer
dimension 1.5-1.8mm dia. and inner dimension
1.3mm dia..
clean sufficiently by cleaning solvents and
remove all residual flux perfectly.
applicable solvent for cleaning. If you use any
other types of solvents, please consult with
Murata factory representative prior to using.
PVZ2 Series Notice
R50E12.pdf 02.9.5
7
1