XE8807AMI026TLF Semtech, XE8807AMI026TLF Datasheet - Page 74

• Manufacturer Part Number: XE8807AMI026TLF
• Description: IC MCU LOW PWR MTP FLASH 32-TQFP
• Manufacturer: Semtech

Specifications of XE8807AMI026TLF

• Applications: Sensing Machine
• Core Processor: RISC
• Program Memory Type: FLASH (11 kB)
• Controller Series: XE8000
• Ram Size: 512 x 8
• Interface: UART, USRT
• Number Of I /o: 24
• Voltage - Supply: 2.4 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 32-TQFP, 32-VQFP
• For Use With: XE8000MP - PROG BOARD AND PROSTART2 CARD
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: XE8807AMI026TR

12.5.2
The table below defines the on-resistance of the switches between the pin and the analog bus for different
conditions. The series resistance between 2 pins of Port B connected to the same analog line is twice the
resistance given in the table.
Note 1: This is the series resistance between the pad and the analog line in 2 cases
Note 2: This is the series resistance in case VBAT ≥ 2.8V and the peripheral VMULT is not present on the circuit.
Note 3: This is the input capacitance seen on the pin when the pin is not connected to an analog line. This value is
indicative only since it is product and package dependent.
Note 4: This is the input capacitance seen on the pin when the pin is connected to an analog line and no other pin
is connected to the same analog line. This value is indicative only since it is product and package dependent.
12.6 Port B function capability
The Port B can be used for different functions implemented by other peripherals. The description below is
applicable only in so far the circuit contains these peripherals.
When the counters are used to implement a PWM function (see the documentation of the counters), the PB[0] and
PB[1] terminals are used as outputs (PB[0] is used if CntPWM0 in RegCntConfig1 is set to 1, PB[1] is used if
CntPWM1 in RegCntConfig1 is set to 1) and the PWM generated values override the values written in RegPBout.
However, PBDir(0) and PBDir(1) are not automatically overwritten and have to be set to 1.
If Output16k is set in RegSysMisc, the frequency is output on PB[3]. This overrides the value contained in
PBOut(3). However, PBDir(3) must be set to 1. The frequency and duty cycle of the clock signal are given in
Figure 12-1. f
Similarly, if OutputCkCpu is set in RegSysMisc, the CPU frequency is output on PB[2]. This overrides the value
contained in PBOut(2). However, PBDir(2) must be set to 1.
© Semtech 2006
sym
Ron
Ron
Cin
Cin
Table 12-10. Analog input specifications.
Port B analog function specification
description
switch resistance
switch resistance
input capacitance (off)
input capacitance (on)
max
1. VBAT ≥ 2.4V and the VMULT peripheral is present on the circuit and enabled.
2. VBAT ≥ 3.0V and the VMULT peripheral is not present on the circuit.
is the frequency of fastest clock present in the circuit.
Figure 12-1. 16 kHz output clock timing
1/fmax
1/f1
Figure 12-2. CPU output clock timing.
min
1/16k
1/f2
3.5
4.5
typ
12-5
max
15
11
unit
kΩ
kΩ
pF
pF
Comments
XE8806A/XE8807A
Note 1
Note 2
Note 3
Note 4
www.semtech.com