AD9834BRUZ Analog Devices Inc, AD9834BRUZ Datasheet - Page 14

• Manufacturer Part Number: AD9834BRUZ
• Description: IC DDS 10BIT 50MHZ LP 20-TSSOP
• Manufacturer: Analog Devices Inc

Specifications of AD9834BRUZ

• Design Resources: Amplitude Control Circuit for AD9834 Waveform Generator (CN0156)
• Resolution (bits): 10 b
• Master Fclk: 50MHz
• Tuning Word Width (bits): 28 b
• Voltage - Supply: 2.3 V ~ 5.5 V
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Surface Mount
• Package / Case: 20-TSSOP
• Transmitting Current: 3.8mA
• Rf Ic Case Style: TSSOP
• No. Of Pins: 20
• Supply Voltage Range: 2.3V To 5.5V
• Operating Temperature Range: -40°C To +105°C
• Msl: MSL 3 - 168 Hours
• Frequency Max: 75MHz
• Filter Terminals: SMD
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-AD9834EBZ - BOARD EVAL FOR AD9834
• Lead Free Status / Rohs Status: Compliant

AD9834
TERMINOLOGY
Integral Nonlinearity (INL)
INL is the maximum deviation of any code from a straight line
passing through the endpoints of the transfer function. The
endpoints of the transfer function are zero scale, a point 0.5 LSB
below the first code transition (000 . . . 00 to 000 . . . 01), and full
scale, a point 0.5 LSB above the last code transition (111 . . . 10 to
111 . . . 11). The error is expressed in LSBs.
Differential Nonlinearity (DNL)
DNL is the difference between the measured and ideal 1 LSB
change between two adjacent codes in the DAC. A specified
DNL of ±1 LSB maximum ensures monotonicity.
Output Compliance
The output compliance refers to the maximum voltage that can
be generated at the output of the DAC to meet the specifications.
When voltages greater than that specified for the output com-
pliance are generated, the AD9834 may not meet the
specifications listed in the data sheet.
Spurious-Free Dynamic Range (SFDR)
Along with the frequency of interest, harmonics of the
fundamental frequency and images of these frequencies are
present at the output of a DDS device. The SFDR refers to the
largest spur or harmonic present in the band of interest. The
wideband SFDR gives the magnitude of the largest harmonic or
Rev. C | Page 14 of 36
spur relative to the magnitude of the fundamental frequency in
the 0 to Nyquist bandwidth. The narrow-band SFDR gives the
attenuation of the largest spur or harmonic in a bandwidth of
±200 kHz about the fundamental frequency.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of harmonics to the rms value
of the fundamental. For the AD9834, THD is defined as
where V
V
through the sixth harmonic.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the measured output signal
to the rms sum of all other spectral components below the
Nyquist frequency. The value for SNR is expressed in decibels.
Clock Feedthrough
There is feedthrough from the MCLK input to the analog
output. Clock feedthrough refers to the magnitude of the
MCLK signal relative to the fundamental frequency in the
output spectrum of the AD9834.
4
, V
THD
5
, and V
1
is the rms amplitude of the fundamental and V
=
20
6
are the rms amplitudes of the second harmonic
log
V
2
2
+
V
3
2
+
V
V
4
1
2
+
V
5
2
+
V
6
2
2
, V
3
,