AD9834BRUZ Analog Devices Inc, AD9834BRUZ Datasheet - Page 27

• Manufacturer Part Number: AD9834BRUZ
• Description: IC DDS 10BIT 50MHZ LP 20-TSSOP
• Manufacturer: Analog Devices Inc

Specifications of AD9834BRUZ

• Design Resources: Amplitude Control Circuit for AD9834 Waveform Generator (CN0156)
• Resolution (bits): 10 b
• Master Fclk: 50MHz
• Tuning Word Width (bits): 28 b
• Voltage - Supply: 2.3 V ~ 5.5 V
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Surface Mount
• Package / Case: 20-TSSOP
• Transmitting Current: 3.8mA
• Rf Ic Case Style: TSSOP
• No. Of Pins: 20
• Supply Voltage Range: 2.3V To 5.5V
• Operating Temperature Range: -40°C To +105°C
• Msl: MSL 3 - 168 Hours
• Frequency Max: 75MHz
• Filter Terminals: SMD
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-AD9834EBZ - BOARD EVAL FOR AD9834
• Lead Free Status / Rohs Status: Compliant

INTERFACING TO MICROPROCESSORS
The AD9834 has a standard serial interface that allows the part
to interface directly with several microprocessors. The device
uses an external serial clock to write the data/control information
into the device. The serial clock can have a frequency of 40 MHz
maximum. The serial clock can be continuous, or it can idle high
or low between write operations. When data/control information is
being written to the AD9834, FSYNC is taken low and is held
low until the 16 bits of data are written into the AD9834. The
FSYNC signal frames the 16 bits of information being loaded
into the AD9834.
AD9834 TO ADSP-21xx INTERFACE
Figure 35 shows the serial interface between the AD9834 and
the ADSP-21xx. The ADSP-21xx should be set up to operate in
the SPORT transmit alternate framing mode (TFSW = 1). The
ADSP-21xx is programmed through the SPORT control register
and should be configured as follows:
• Internal clock operation (ISCLK = 1)
• Active low framing (INVTFS = 1)
• 16-bit word length (SLEN = 15)
• Internal frame sync signal (ITFS = 1)
• Generate a frame sync for each write (TFSR = 1)
Transmission is initiated by writing a word to the Tx register
after the SPORT has been enabled. The data is clocked out on
each rising edge of the serial clock and clocked into the AD9834
on the SCLK falling edge.
1
ADDITIONAL PINS OMITTED FOR CLARITY.
ADSP-21xx
Figure 35. ADSP-21xx to AD9834 Interface
SCLK
TFS
1
DT
FSYNC
SDATA
SCLK
AD9834
1
Rev. C | Page 27 of 36
AD9834 TO 68HC11/68L11 INTERFACE
Figure 36 shows the serial interface between the AD9834 and
the 68HC11/68L11 microcontroller. The microcontroller is
configured as the master by setting Bit MSTR in the SPCR to 1,
providing a serial clock on SCK while the MOSI output drives
the serial data line SDATA. Because the microcontroller does
not have a dedicated frame sync pin, the FSYNC signal is
derived from a port line (PC7). The setup conditions for correct
operation of the interface are as follows:
• SCK idles high between write operations (CPOL = 0)
• Data is valid on the SCK falling edge (CPHA = 1)
When data is being transmitted to the AD9834, the FSYNC line is
taken low (PC7). Serial data from the 68HC11/68L11 is transmitted
in 8-bit bytes with only eight falling clock edges occurring in the
transmit cycle. Data is transmitted MSB first. To load data into
the AD9834, PC7 is held low after the first eight bits are transferred
and a second serial write operation is performed to the AD9834.
Only after the second eight bits have been transferred should
FSYNC be taken high again.
1
ADDITIONAL PINS OMITTED FOR CLARITY.
68HC11/68L11
Figure 36. 68HC11/68L11 to AD9834 Interface
MOSI
SCK
PC7
1
FSYNC
SDATA
SCLK
AD9834
1
AD9834