AD9945KCP Analog Devices Inc, AD9945KCP Datasheet - Page 13

IC CCD SIGNAL PROCESSOR 32-LFCSP

AD9945KCP

Manufacturer Part Number
AD9945KCP
Description
IC CCD SIGNAL PROCESSOR 32-LFCSP
Manufacturer
Analog Devices Inc
Type
CCD Signal Processor, 12-Bitr
Datasheets

Specifications of AD9945KCP

Rohs Status
RoHS non-compliant
Input Type
Logic
Output Type
Logic
Interface
3-Wire Serial
Mounting Type
Surface Mount
Package / Case
32-LFCSP
Analog Front End Type
CCD
Analog Front End Category
Video
Interface Type
Serial (3-Wire)
Sample Rate
40MSPS
Input Voltage Range
0.5V
Operating Supply Voltage (min)
2.7V
Operating Supply Voltage (typ)
3V
Operating Supply Voltage (max)
3.6V
Resolution
12b
Number Of Adc's
1
Power Supply Type
Analog/Digital
Operating Temp Range
-20C to 85C
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Pin Count
32
Package Type
LFCSP EP
Number Of Channels
1
Current - Supply
-
Lead Free Status / RoHS Status
Not Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD9945KCP
Manufacturer:
ADI
Quantity:
455
Part Number:
AD9945KCPZ
Manufacturer:
ADI44
Quantity:
300
Part Number:
AD9945KCPZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD9945KCPZ
Quantity:
750
Part Number:
AD9945KCPZRL7
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Internal Power-On Reset Circuitry
After power-on, the AD9945 will automatically reset all internal
registers and perform internal calibration procedures. This takes
approximately 1 ms to complete. During this time, normal clock
signals and serial write operations may occur. However, serial
register writes will be ignored until the internal reset operation
is completed.
Grounding and Decoupling Recommendations
As shown in Figure 11, a single ground plane is recommended for
the AD9945. This ground plane should be as continuous as
possible. This will ensure that all analog decoupling capacitors
provide the lowest possible impedance path between the power
REV. A
OUTPUTS
DATA
NOTE
THE EXPOSED PAD ON THE BOTTOM OF THE AD9945 SHOULD BE
SOLDERED TO THE GND PLANE OF THE PRINTED CIRCUIT BOARD
12
Figure 11. Recommended Circuit Configuration for CCD Mode
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
SUPPLY
DRIVER
1
2
3
4
5
6
7
8
INTERFACE
3V
SERIAL
0.1 F
PIN 1
IDENTIFIER
(Not to Scale)
TOP VIEW
AD9945
3
0.1 F
–13–
3V
ANALOG
SUPPLY
and bypass pins and their respective ground pins. All decoupling
capacitors should be located as close as possible to the package
pins. A single clean power supply is recommended for the AD9945,
but a separate digital driver supply may be used for DRVDD
(Pin 11). DRVDD should always be decoupled to DRVSS (Pin 12),
which should be connected to the analog ground plane. Advan-
tages of using a separate digital driver supply include using a
lower voltage (2.7 V) to match levels with a 2.7 V ASIC, reducing
digital power dissipation, and reducing potential noise coupling.
If the digital outputs (Pins 1 to 10, 31, and 32) must drive a
load larger than 20 pF, buffering is recommended to reduce
digital code transition noise. Alternatively, placing series resis-
tors close to the digital output pins may also help reduce noise.
24
23
22
21
20
19
18
17
NC = NO CONNECT
REFB
REFT
CCDIN
AVSS
AVDD
SHD
SHP
CLPOB
0.1 F
1.0 F
1.0 F
5
CLOCK
INPUTS
0.1 F
3V
ANALOG
SUPPLY
CCDIN
AD9945

Related parts for AD9945KCP