AD9945KCP Analog Devices Inc, AD9945KCP Datasheet - Page 6

• Manufacturer Part Number: AD9945KCP
• Description: IC CCD SIGNAL PROCESSOR 32-LFCSP
• Manufacturer: Analog Devices Inc
• Type: CCD Signal Processor, 12-Bitr

Specifications of AD9945KCP

• Rohs Status: RoHS non-compliant
• Input Type: Logic
• Output Type: Logic
• Interface: 3-Wire Serial
• Mounting Type: Surface Mount
• Package / Case: 32-LFCSP
• Analog Front End Type: CCD
• Analog Front End Category: Video
• Interface Type: Serial (3-Wire)
• Sample Rate: 40MSPS
• Input Voltage Range: 0.5V
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (typ): 3V
• Operating Supply Voltage (max): 3.6V
• Resolution: 12b
• Number Of Adc's: 1
• Power Supply Type: Analog/Digital
• Operating Temp Range: -20C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 32
• Package Type: LFCSP EP
• Number Of Channels: 1
• Current - Supply: -
• Lead Free Status / RoHS Status: Not Compliant

AD9945
DEFINITIONS OF SPECIFICATIONS
Differential Nonlinearity (DNL)
An ideal ADC exhibits code transitions that are exactly 1 LSB
apart. DNL is the deviation from this ideal value. Thus, every
code must have a finite width. No missing codes guaranteed to
12-bit resolution indicates that all 4096 codes must be present
over all operating conditions.
Peak Nonlinearity
Peak nonlinearity, a full signal chain specification, refers to the
peak deviation of the output of the AD9945 from a true straight
line. The point used as zero scale occurs 1/2 LSB before the first
code transition. Positive full scale is defined as a level 1 1/2 LSB
beyond the last code transition. The deviation is measured from
the middle of each particular output code to the true straight line.
The error is then expressed as a percentage of the 2 V ADC full-
scale signal. The input signal is always appropriately gained up to
fill the ADC’s full-scale range.
Total Output Noise
The rms output noise is measured using histogram techniques.
The standard deviation of the ADC output codes is calculated in
LSB and represents the rms noise level of the total signal chain
EQUIVALENT INPUT CIRCUITS
THREE-
STATE
DATA
Figure 2. Data Outputs—D0 to D11
Figure 1. Digital Inputs—SHP, SHD,
DATACLK, CLPOB, PBLK, SCK, SL, SDATA
330
DVDD
DVSS
DVDD
DVSS
DRVDD
DRVSS
DOUT
–6–
at the specified gain setting. The output noise can be converted
to an equivalent voltage, using the relationship
where N is the bit resolution of the ADC. For the AD9945,
1 LSB is 0.5 mV.
Power Supply Rejection (PSR)
The PSR is measured with a step change applied to the supply
pins. This represents a very high frequency disturbance on the
AD9945’s power supply. The PSR specification is calculated
from the change in the data outputs for a given step change in
the supply voltage.
Internal Delay for SHP/SHD
The internal delay (also called aperture delay) is the delay that
occurs from the time when a sampling edge is applied to the
AD9945 until the actual sample of the input signal is held. Both
SHP and SHD sample the input signal during the transition from
low to high, so the internal delay is measured from each clock’s
rising edge to the instant the actual internal sample is taken.
1 LSB = (ADC Full Scale/2
Figure 3. CCDIN (Pin 22)
AVDD
AVSS
60
N
AVSS
codes)
REV. B