GP2W0004YP Sharp Microelectronics, GP2W0004YP Datasheet
GP2W0004YP
Specifications of GP2W0004YP
Available stocks
Related parts for GP2W0004YP
GP2W0004YP Summary of contents
Page 1
... IC controller. The LED may be connected to the device battery or some other higher level source. The GP2W0004YP also includes an integral echo- cancel function that disables the RX Data Output when the Transmit LED is driven by TX data. The transceiver module has a built-in shutdown mode for those applications that are very conscious about current consumption ...
Page 2
... OPERATING CONDITIONS V 2 4.0 (MAX.) LEDA 2/3 × IHTXD ) V 1/3 × ILTXD BR 9.6 to 115 – 0.5 IHSD ILSD T -25 to +85 OPR , P Infrared Transceiver FRONT PIN 1 PIN 6 REAR PIN 6 PIN 1 GP2W0004YP-6 Figure 1. Package Orientation UNIT CONDITIONS 2 5 kbit °C IrDA Technical Information ...
Page 3
... T 1 Figure 2. Input Signal Waveform, Detector Side TRANSMITTER (NOTE 1) NOTE: 1. Transmitter uses GP2W0004YP ( p = 870 nm TYP.) with the radiation intensity attenuated to 3.6 mW/sr. 2. Indicates horizontal and vertical directions. 3. Ee: Detector face illuminance < Figure 5. Standard Optical System, Detector Side IrDA Technical Information ...
Page 4
... Figure 6 provides some approximate external passive values for design reference. See the specification for complete optical/electrical characteristic data. Application Circuit and External Passives The application circuit and external passives shown in Figure 6 enable GP2W0004YP to operate at both one meter and low power option communica- tion mode 3 ...
Page 5
... Infrared Transceiver Signal Waveform Example Figure 9 provides examples of each waveform when correctly operating the GP2W0004YP in a manner con- forming to IrDA standards. Refer to the Basic System Block Diagram in Figure 8 for the positions that corre- spond to each waveform. Note that the IrDA bit stream is inverted in the encoder and decoder circuits, and the output pulse is sent during a ‘ ...
Page 6
... GP2W0004YP/XP Solder Paste Footprint GP2W0004YP is shown in Figure 11. Note that the shield contact for GP2W0004YP is applied through the Ground pin in position 6. The shield is soldered to the back of the transceiver at the ground pin, and a sepa- rate contact for a ground tab is not required GP2W0004XP is shown in Figure 12. ...
Page 7
... IrDA Serial Infrared Physi- cal Layer Link Specification. Any values to be calcu- lated with these formula must be given in mm. ˚ Figure 13. IR Window Cosmetic Design GP2W0004YP/XP L ˚ (3.15) ˚ 18 GP2W0004YP-12 7 ...
Page 8
... IR window. If the vendor does not know what you are talking about, you need to find a knowledgeable source for filter materials. 400 500 600 700 WAVELENGTH, nm Figure 14. Highpass Filter Characteristics Infrared Transceiver 800 900 1,000 1,100 GP2W0004YP-13 IrDA Technical Information ...
Page 9
... The temperature/time details are described in Table GP2W0004YP molded pinout joints are heated to a temperature of 165°C to activate the flux in the solder paste. The temperature ramp-up rate R1 should be within the range of 1°C to 5°C per second. Package ...
Page 10
... C MAX. 200 C 165 C MAX. 150 C 100 NOTE: 1. Heat Up 2. Solder Paste Dry 3. Solder Reflow 4. Cooling Figure 15. IR Solder Reflow Temperature Profile 120 sec. MAX. TIME 1 2 PROCESS SECTIONS Infrared Transceiver R3 10 sec. MAX. 60 sec. MAX. 90 sec. MAX GP2W0004YP-16 IrDA Technical Information ...
Page 11
... Infrared Transceiver Evaluation Board The circuit diagram in Figure 16 is the recom- mended evaluation circuit for the GP2W0004YP. This circuit is provided on an evaluation board for test and evaluation purposes. Samples are available through your Sharp support office, Sales Representative, or Distributor. The resistor value for R ...
Page 12
... Outer Case Pads TAPE AND REEL Figures 17 through 19 show the reel dimensions and product orientation in the reel. GP2W0004YP is the side view device, and GP2W0004XP is the top view device. Note that the device orientation in the reel is not the same for both devices. 21 ± ...
Page 13
... Infrared Transceiver Figure 18. Direction of Product Insertion (GP2W0004YP) Figure 19. Direction of Product Insertion (GP2W0004XP) ORDERING INFORMATION Table 6 shows the correct ordering information for the device in both the top view and side view orientation. Table 6. Ordering Information MODEL NUMBER ORIENTATION GP2W0004YP Side View GP2W0004XP ...
Page 14
... GP2W0004YP/XP Packing Method Table 7 provides information on how each tape reel is packaged. Each aluminum laminate bag contains one reel (2,000 devices per reel) and desiccant. Four reels in their bags are packed per carton (4 reels/car- ton; 8,000 transceivers per carton). The outer carton will then be sealed with craft tape, with indication of model name, quantity, and outgoing inspection date on the case ...
Page 15
... GP2W0004YP/XP SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited Warranty for SHARP’s product warranty. The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied. ...