PS21963-AET Mitsumi Electronics, Corp., PS21963-AET Datasheet
PS21963-AET
Related parts for PS21963-AET
PS21963-AET Summary of contents
Page 1
... Fault signaling : Corresponding fault (Lower-leg IGBT fault (Lower-side supply fault (LVIC temperature). • Input interface : 3V, 5V line (High Active). • UL Approved : Yellow Card No. E80276 APPLICATION AC100V~200V three-phase inverter drive for small power motor control. Fig. 1 PACKAGE OUTLINES (PS21963-ET) 38 ±0.5 20×1.778(=35.56) 0.28 35 ± ...
Page 2
... Fig. 2 LONG TERMINAL TYPE PACKAGE OUTLINES (PS21963-AET) 38 ±0.5 20×1.778(=35.56) 0.28 35 ±0.3 ±0.2 1.778 17 QR Type name Code Lot No. 3 MIN 18 0.28 2.54 ±0.2 14×2.54 (=35.56) 0.5 HEAT SINK SIDE *) Two V terminals (9 & 16 pin) are connected inside DIPIPM, please connect either one to the 15V power supply GND outside and NC leave another one open ...
Page 3
... Fig. 4 BOTH SIDES ZIGZAG TERMINAL TYPE PACKAGE OUTLINES (PS21963-ETW) 38 ±0.5 20×1.778(=35.56) 0.28 ±0.3 35 1.778 ±0. Type name Code Lot No. 3 MIN 18 0.28 ±0.25 2.54 14×2.54(=35.56) 0.5 HEAT SINK SIDE *) Two V terminals (9 & 16 pin) are connected inside DIPIPM, please connect either one to the 15V power supply GND outside and NC leave another one open ...
Page 4
... FO Current sensing input voltage V SC PS21963-ET/-AET/-CET/-ETW Short Circuit Protective Function (SC protection is achieved by sensing the L-side DC-Bus current (through the external shunt resistor) after allowing a suitable filtering time (defined by the RC circuit). When the sensed shunt voltage exceeds the SC trip-level, all the L-side IGBTs are turned OFF and a fault signal (Fo) is output ...
Page 5
... Switching times c(on) t off t c(off) Collector-emitter cut-off I CES current PS21963-ET/-AET/-CET/-ETW Condition V = 13.5~16.5V, Inverter part 125°C, non-repetitive, less than 2µs j 60Hz, Sinusoidal, 1 minute, Between pins and heat-sink plate Control terminals 3mm T point C Heat sink side Power terminals ...
Page 6
... period, however, the minimum F MECHANICAL CHARACTERISTICS AND RATINGS Parameter Mounting torque Weight Heat-sink flatness Note 7 : Plain washers (ISO 7089~7094) are recommended. Note 8: Flatness measurement position Measurement position + – Heat sink side PS21963-ET/-AET/-CET/-ETW Condition 15V Total ...
Page 7
... VFB WFB PS21963-ET/-AET/-CET/-ETW Condition Applied between P-N Applied between Applied between V - UFB VFB WFB ≤ 100°C For each input signal ≤ 100°C, Tj ≤ 125°C ...
Page 8
... UV period b6. Under voltage reset ( b7. Normal operation : IGBT ON and carrying current. Control input Protection circuit state Control supply voltage V Output current Ic Error output Fo PS21963-ET/-AET/-CET/-ETW a6 a7 SET RESET reference voltage CR circuit time ...
Page 9
... The DIPIPM input section integrates a 3.3kΩ (min) pull-down resistor. Therefore, when using an external fil- tering resistor, pay attention to the turn-on threshold voltage. Fig. 10 WIRING CONNECTION OF SHUNT RESISTOR PS21963-ET/-AET/-CET/-ETW ) DB , the circuits start to operate when next input is applied. ...
Page 10
... It is recommended to insert a Zener diode (24V/1W) between each pair of control supply terminals to prevent surge destruction control GND is connected to power GND by broad pattern, it may cause malfunction by power GND fluctuation recommended to connect control GND and power GND at only a point. PS21963-ET/-AET/-CET/-ETW C2 C1 ...