SAM9G10 Atmel Corporation, SAM9G10 Datasheet - Page 875

• Manufacturer Part Number: SAM9G10
• Manufacturer: Atmel Corporation

Specifications of SAM9G10

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 266 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 1
• Uart: 4
• Ssc: 3
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

• TXEMPTY: Transmitter Empty
0: There are characters in either US_THR or the Transmit Shift Register, or the transmitter is disabled.
1: There are no characters in US_THR, nor in the Transmit Shift Register.
• ITER: Max number of Repetitions Reached
0: Maximum number of repetitions has not been reached since the last RSTSTA.
1: Maximum number of repetitions has been reached since the last RSTSTA.
• UNRE: SPI Underrun Error
– Applicable if USART operates in SPI Slave Mode (USART_MODE = 0xF):
UNRE = 0: No SPI underrun error has occurred since the last RSTSTA.
UNRE = 1: At least one SPI underrun error has occurred since the last RSTSTA.
• NACK: Non Acknowledge Interrupt
0: Non Acknowledge has not been detected since the last RSTNACK.
1: At least one Non Acknowledge has been detected since the last RSTNACK.
• LINBK: LIN Break Sent or LIN Break Received
– Applicable if USART operates in LIN Master Mode (USART_MODE = 0xA):
0: No LIN Break has been sent since the last RSTSTA.
1:At least one LIN Break has been sent since the last RSTSTA
– If USART operates in LIN Slave Mode (USART_MODE = 0xB):
0: No LIN Break has received sent since the last RSTSTA.
1:At least one LIN Break has been received since the last RSTSTA.
• LINID: LIN Identifier Sent or LIN Identifier Received
0: No LIN Identifier has been sent since the last RSTSTA.
1:At least one LIN Identifier has been sent since the last RSTSTA.
0: No LIN Identifier has been received since the last RSTSTA.
1:At least one LIN Identifier has been received since the last RSTSTA
• LINTC: LIN Transfer Completed
0: The USART is idle or a LIN transfer is ongoing.
1: A LIN transfer has been completed since the last RSTSTA.
• CTSIC: Clear to Send Input Change Flag
0: No input change has been detected on the CTS pin since the last read of US_CSR.
1: At least one input change has been detected on the CTS pin since the last read of US_CSR.
• CTS: Image of CTS Input
11053B–ATARM–22-Sep-11
11053B–ATARM–22-Sep-11
– If USART operates in LIN Master Mode (USART_MODE = 0xA):
– If USART operates in LIN Slave Mode (USART_MODE = 0xB):
SAM9G35
SAM9G35
875
875