LMC1982CIN National Semiconductor, LMC1982CIN Datasheet - Page 6

• Manufacturer Part Number: LMC1982CIN
• Description: IC CTRLR DGTL STEREO TONE 28DIP
• Manufacturer: National Semiconductor
• Type: Tone and Volume Controlr

Specifications of LMC1982CIN

• Applications: Audio Systems
• Mounting Type: Through Hole
• Package / Case: *
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: *LMC1982CIN

www.national.com
Connection Diagrams
Pin Description
CLK (1)
DIGITAL INPUT
1 & 2 (2, 3)
INPUTS 1 & 2
(4, 25; 5, 24)
SELECT OUT
(6, 23)
SELECT IN
(7, 22)
TONE IN
(8, 21)
TONE OUT
(9, 20)
OP AMP
OUT (10, 19)
See NS Package Number N28B
Order Number LMC1982CIN
The INTERMETAL (IM) Bus clock is applied
to the CLOCK pin. This input accepts a TTL
or CMOS level signal. The input is used to
clock the DATA signal. A data bit must be
valid on the rising clock edge.
Internally tied high to V
pull-up resistor, these inputs allow a periph-
eral device to place any single-bit, active low
digital information onto the IM Bus. It is then
sent out to the controlling device through the
DATA pin. Examples of such information
could include indication of the presence of a
Second Audio Program (SAP) or an FM ste-
reo carrier.
These are the LMC1982’s two stereo input
pairs.
The selected INPUT signal is available at this
output. This feature allows external signal
processors such as noise reduction or
graphic equalizers to be used. This output
can typically sink 1 mA. These pins should be
capacitively coupled to pins 7 and 22, re-
spectively, if no external processor is used.
These are the inputs that an external signal
processor uses to return a signal to the
LMC1982. These pins should be capacitively
coupled to pins 6 and 23, respectively, if no
external processor is used.
These are the inputs to the tone control am-
plifier. See the Application Information sec-
tion titled “Tone Control Response”.
Tone control amplifier output. See the Appli-
cation Information section titled “Tone Control
Response”.
These outputs are used with external tone
control capacitors. Internally, this output is
applied to the volume attenuators.
Top View
+
through a 30 k
DS011028-2
6
LOUDNESS
(11, 18)
ENHANCED
STEREO
(12, 17)
MAIN
OUTPUT
(13, 16)
BYPASS (14) A 10 µF capacitor is connected between this
GROUND (15) This pin is connected to analog ground.
V
ID (27)
DATA (28)
+
(26)
See NS Package Number V28A
Order Number LMC1982CIV
The output signal on these pins is a voltage
taken from the volume attenuator’s −40 dB
tap point. An external R–C network is con-
nected to these pins.
An external R–C network is connected
across these pins. This provides left-right
channel cross-coupling and cancellation to
create an enhanced stereo channel separa-
tion effect.
The output signal from these pins drives a
stereo power amplifier. The output can typi-
cally sink 1 mA.
pin and ground to provide an AC ground for
the internal half-supply voltage reference.
This is the power supply connection. The
LMC1982 is operational with supply voltages
from 6V to 12V. This pin should be bypassed
to ground through a 1.0 µF capacitor.
This is the IDENTITY digital input that, when
low, signals the LMC1982 to receive, from a
controlling
(40
This is the serial data input for communica-
tions sent by a controller. The controller must
have open drain outputs used with external
pull-up resistors. The data rate has a maxi-
mum frequency of 1 MHz. The LMC1982 re-
quires 16 bits of data to control or change a
function: the first 8 bits select the LMC1982
and one of eight functions. The final eight bits
set the function to a desired value. The data
must be valid on the rising edge of the
CLOCK input signal.
H
–47
H
), present on the DATA line.
Top View
device,
a
device
DS011028-12
address