TS87C54X2 Temic Semiconductors, TS87C54X2 Datasheet - Page 38

no-image

TS87C54X2

Manufacturer Part Number
TS87C54X2
Description
8-bit CMOS Microcontroller 0-60 MHz
Manufacturer
Temic Semiconductors
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
TS87C54X2-LCA
Manufacturer:
CYPRESS
Quantity:
13
Part Number:
TS87C54X2-LCB
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
TS87C54X2-LCC
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
TS87C54X2-LCE
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
TS87C54X2-LIB
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
TS87C54X2-LIC
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
TS87C54X2-MCB
Manufacturer:
ATMEL
Quantity:
500
Part Number:
TS87C54X2-MCB
Manufacturer:
TEMIC
Quantity:
20 000
Part Number:
TS87C54X2-MCC
Manufacturer:
TEMIC
Quantity:
245
Part Number:
TS87C54X2-MCC
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
TS87C54X2-MCE
Manufacturer:
ATMEL
Quantity:
5
Part Number:
TS87C54X2-MIB
Manufacturer:
ATMEL
Quantity:
27
TS80C54X2/C58X2
TS87C54X2/C58X2
8.3.3 Programming Algorithm
The Improved Quick Pulse algorithm is based on the Quick Pulse algorithm and decreases the number of pulses
applied during byte programming from 25 to 1.
To program the TS80C54/58X2 the following sequence must be exercised:
Repeat step 2 through 6 changing the address and data for the entire array or until the end of the object file is
reached (See Figure 12.).
8.3.4 Verify algorithm
Code array verify must be done after each byte or block of bytes is programmed. In either case, a complete verify
of the programmed array will ensure reliable programming of the TS87C54/58X2.
P 2.7 is used to enable data output.
To verify the TS87C54/58X2 code the following sequence must be exercised:
Repeat step 2 through 3 changing the address for the entire array verification (See Figure 12.)
The encryption array cannot be directly verified. Verification of the encryption array is done by observing that the
code array is well encrypted.
38
* See Table 31. for proper value on these inputs
Step 1: Activate the combination of control signals.
Step 2: Input the valid address on the address lines.
Step 3: Input the appropriate data on the data lines.
Step 4: Raise EA/VPP from VCC to VPP (typical 12.75V).
Step 5: Pulse ALE/PROG once.
Step 6: Lower EA/VPP from VPP to VCC
Step 1: Activate the combination of program and control signals.
Step 2: Input the valid address on the address lines.
Step 3: Read data on the data lines.
PROGRAM
SIGNALS*
CONTROL
SIGNALS*
4 to 6 MHz
Figure 11. Set-Up Modes Configuration
PSEN
P2.6
P2.7
P3.3
P3.6
P3.7
XTAL1
EA/VPP
ALE/PROG
RST
P0.0-P0.7
P1.0-P1.7
P2.0-P2.5,
P3.4
VCC
VSS
GND
+5V
D0-D7
A0-A7
A8-A14
Rev. B - Aug. 31, 1999

Related parts for TS87C54X2