sy89533l Micrel Semiconductor, sy89533l Datasheet
sy89533l
Available stocks
Related parts for sy89533l
sy89533l Summary of contents
Page 1
... For applications that must interface to a crystal oscillator, see the SY89532/33. Data sheets and support documentation can be found on Micrel’s web site at www.micrel.com. PRODUCT SELECTION GUIDE Input Device Crystal SY89532L* X SY89533L* X SY89534L SY89535L *Refer to SY89532/33L data sheet for details. 1 Precision Edge ® Precision Edge SY89534/35L ...
Page 2
Micrel, Inc. PACKAGE/ORDERING INFORMATION NC* 1 NC* 2 NC* 3 VCO_SEL 4 PSEL1 5 PSEL0 6 LOOP_REF 7 64-pin LOOP_FILTER 8 EPAD-TQFP GND 9 ...
Page 3
Micrel, Inc. PIN DESCRIPTION Power Pin Number Pin Name 60 CC_Logic 62 V CCA CCO 30, 31 CCO CCO 4, 9, 25, 63, 29 GND (exposed pad) Configuration Pin ...
Page 4
Micrel, Inc. ABSOLUTE MAXIMUM RATINGS Symbol All V V Pin Potential to Ground Pin Input Voltage Output Current OUT T Lead Temperature (soldering, 20sec.) LEAD T Storage Temperature store Package Thermal Resistance (Junction-to-Ambient) JA ...
Page 5
Micrel, Inc. DC ELECTRICAL CHARACTERISTICS REFCLK (pins 10, 11) INPUT (All V Symbol Parameter V Differential Input Voltage ID V Input HIGH Voltage IH V Input LOW Voltage IL 100K LVPECL Outputs (All V pins = +3.3V 10%) CC Symbol ...
Page 6
Micrel, Inc. AC ELECTRICAL CHARACTERISTICS All V pins = +3.3V 10% CC Symbol Parameter f Reference Input Frequency IN f Output Frequency Range OUT t Internal VCO Frequency Range VCO (11) t Within Device Within Bank skew Bank-to-Bank (12) Part-to-Part ...
Page 7
Micrel, Inc. TIMING DIAGRAMS (Conditions: Internal VCO, unless otherwise stated.) VCO FSEL FOUT OUT_SYNC VCO FSEL FOUT OUT_SYNC M9999-110405 hbwhelp@micrel.com or (408) 955-1690 001 010 t OUTPUT_SYNC t SETUP_FSEL t OUTPUT_RESET t HOLD_FSEL Frequency Programming 001 010 f to VALID ...
Page 8
... PLL driven by a differential or single-ended reference input. For users who wish to supply a crystal input, please use the SY89532L or SY89533L. The PLL output is sent to three banks of outputs. Each bank has its own programmable frequency divider, and the design is optimized to provide very low skew between banks, and very low jitter ...
Page 9
Micrel, Inc. Output Logic Characteristics See “Output Termination Recommendations” for illustrations. In cases where single-ended output is desired, the designer should terminate the unused complimentary output in the same manner as the normal output that is being used. Unused LVPECL ...
Page 10
Micrel, Inc. PRE-DIVIDE FREQUENCY SELECT TABLE (PSEL) PSEL1 (MSB) PSEL0 POST-DIVIDE FREQUENCY SELECT TABLE (FSEL) (1) FSEL_A2 (MSB) FSEL_A1 ...
Page 11
Micrel, Inc. FEEDBACK DIVIDE SELECT TABLE (MSEL ...
Page 12
Micrel, Inc. INPUT INTERFACE V V CC(DRIVER) CC(534/5) TTL REFCLK LVTTL /REFCLK 2.5k SY89534L 1% SY89535L Figure 4a. 5V, 3.3V “TTL” 2.3V to 2.7V V 2.5V REFCLK LVTTL /REFCLK 2.5k SY89534L 1% SY89535L Figure 4c. 2.5V “LVTTL” REFCLK ...
Page 13
Micrel, Inc CC(DRIVER CML 130 130 1% 1% Figure 4g. CML-AC Coupled–Long Trace Lengths V DDQ 105 1% SSTL_2 100 1% Figure 4i. SSTL_2 M9999-110405 hbwhelp@micrel.com or (408) 955-1690 V CC REFCLK /REFCLK ...
Page 14
Micrel, Inc. OUTPUT TERMINATION RECOMMENDATIONS +3.3V “Source” Figure 5. PECL Parallel Termination–Thevenin Equivalent “Source” NOTES: 1. PECL Y-termination is a power-saving alternative to Thevenin termination. 2. Place termination resistors as close to destination inputs as possible resistor sets ...
Page 15
Micrel, Inc. 64-PIN EPAD-TQFP (DIE UP) (H64-1) +0.03 –0.03 +0.012 –0.012 Heat Dissipation PCB Thermal Consideration for 64-Pin EPAD-TQFP Package MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA + 1 (408) 944-0800 TEL The information furnished by Micrel ...