pca9510a NXP Semiconductors, pca9510a Datasheet

no-image

pca9510a

Manufacturer Part Number
pca9510a
Description
Hot Swappable I2c-bus And Smbus Bus Buffer
Manufacturer
NXP Semiconductors
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
pca9510aD
Manufacturer:
NXP
Quantity:
12 000
Part Number:
pca9510aD
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
pca9510aD
Quantity:
20
Part Number:
pca9510aD,118
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
pca9510aDP
Manufacturer:
PHIL
Quantity:
3 083
Part Number:
pca9510aDP
Manufacturer:
PHILIPS
Quantity:
1 200
Part Number:
pca9510aDP
Manufacturer:
NXP/恩智浦
Quantity:
20 000
1. General description
2. Features
The PCA9510A is a hot swappable I
insertion into a live backplane without corrupting the data and clock buses. Control
circuitry prevents the backplane from being connected to the card until a stop command or
bus idle occurs on the backplane without bus contention on the card. When the
connection is made, the PCA9510A provides bidirectional buffering, keeping the
backplane and card capacitances isolated.
The PCA9510A has no rise time accelerator circuitry to prevent interference when there
are multiple devices in the same system. The PCA9510A incorporates a digital ENABLE
input pin, which enables the device when asserted HIGH and forces the device into a Low
current mode when asserted LOW, and an open-drain READY output pin, which indicates
that the backplane and card sides are connected together (HIGH) or not (LOW).
During insertion, the PCA9510A SDAIN and SCLIN pins (inputs only) are precharged to
1 V to minimize the current required to charge the parasitic capacitance of the chip.
Remark: The dynamic offset design of the PCA9510A/11A/12A/13A/14A I/O drivers allow
them to be connected to another PCA9510A/11A/12A/13A/14A device in series or in
parallel and to the A side of the PCA9517. The PCA9510A/11A/12A/13A/14A cannot
connect to the static offset I/Os used on the PCA9515/15A/16/16A/18 or PCA9517 B side
or P82B96 Sx/y side.
PCA9510A
Hot swappable I
Rev. 01 — 8 September 2005
Bidirectional buffer for SDA and SCL lines increases fanout and prevents SDA and
SCL corruption during live board insertion and removal from multi-point backplane
systems
Compatible with I
Active HIGH ENABLE input
Active HIGH READY open-drain output
High-impedance SDAn and SCLn pins for V
1 V precharge on SDAIN and SCLIN inputs
Supports clock stretching and multiple master arbitration and synchronization
Operating power supply voltage range: 2.7 V to 5.5 V
I/Os are not 5.5 V tolerant
0 Hz to 400 kHz clock frequency
ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM per
JESD22-A115, and 1000 V CDM per JESD22-C101
Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA
Packages offered: SO8, TSSOP8 (MSOP8)
2
C-bus Standard mode, I
2
C-bus and SMBus bus buffer
2
C-bus and SMBus buffer that allows I/O card
2
C-bus Fast mode, and SMBus standards
CC
= 0 V
Product data sheet

Related parts for pca9510a

pca9510a Summary of contents

Page 1

... LOW, and an open-drain READY output pin, which indicates that the backplane and card sides are connected together (HIGH) or not (LOW). During insertion, the PCA9510A SDAIN and SCLIN pins (inputs only) are precharged minimize the current required to charge the parasitic capacitance of the chip. ...

Page 2

... PCA9510AD PA9510A SO8 PCA9510ADP 9510A TSSOP8 [1] Also known as MSOP8. Standard packing quantities and other packaging data are available at www.standardics.philips.com/packaging/ . PCA9510A_1 Product data sheet Hot swappable I PCA9510A PCA9511A PCA9512A PCA9513A PCA9514A yes = 0 V yes yes - in only - Description plastic small outline package; 8 leads; body width 3.9 mm [1] plastic thin shrink small outline package ...

Page 3

... SDAIN CONNECT 100 k RCH1 100 k RCH2 SCLIN CONNECT 0.55V / CC 0.45V CC UVLO 100 s ENABLE DELAY Fig 1. Block diagram of PCA9510A PCA9510A_1 Product data sheet Hot swappable I BACKPLANE-TO-CARD CONNECTION CONNECT CONNECT ENABLE 1 VOLT PRECHARGE BACKPLANE-TO-CARD CONNECTION CONNECT STOP BIT AND BUS IDLE 0.5 A ...

Page 4

... Figure 1 “Block diagram of PCA9510A”. Rev. 01 — 8 September 2005 PCA9510A 2 Hot swappable I C-bus and SMBus bus buffer ENABLE 1 SCLOUT 2 PCA9510ADP SCLIN 3 GND 4 002aab783 Fig 3. Pin configuration for TSSOP8 ) and remaining en © Koninklijke Philips Electronics N.V. 2005. All rights reserved ...

Page 5

... The PCA9510A (rise time accelerator is permanently disabled) and the PCA9512A (rise time accelerator can be turned off) are a little different with the rise time accelerator turned off because the rise time accelerator will not pull the node up, but the same logic that turns ...

Page 6

... CC Rev. 01 — 8 September 2005 PCA9510A 2 Hot swappable I C-bus and SMBus bus buffer is above 0.6 V and a rising edge is ...

Page 7

... C is the pull-up resistor value for V PU Figure 5 and Figure 6 for guidance in resistor pull-up selection. Rev. 01 — 8 September 2005 PCA9510A 2 Hot swappable I C-bus and SMBus bus buffer CC is the minimum V CC(min for PU = 3.6 V maximum. The start-up circuitry CC © ...

Page 8

... Placing a bus buffer on the edge of each card, however, isolates the card capacitance from the backplane. For a given I/O card, the PCA9510A drives the capacitance of everything on the card and the backplane must drive only the capacitance of the bus buffer, which is less than 10 pF, the connector, trace, and all additional cards on the backplane. See Application Note AN10160, ‘ ...

Page 9

... SDA SCL Remark: The PCA9510A can be used in any combination depending on the number of rise time accelerators that are needed by the system. Normally only one PCA9510A would be required per bus. Fig 7. Hot swapping multiple I/O cards into a backplane using the PCA9510A in a cPCI, VME, and AdvancedTCA ...

Page 10

... Philips Semiconductors BACKPLANE CONNECTOR BACKPLANE SDA SCL Fig 8. Hot swapping multiple I/O cards into a backplane using the PCA9510A in a PCI system ENABLE SDA1 SDAIN SCLIN SCL1 to other System 1 devices Remark: See Application Note AN255, ‘I2C repeaters, hubs, and expanders’ for more information on other devices better optimized for long distance transmission of the I Fig 9 ...

Page 11

... SDAIN 1 ENABLE ENABLE Limiting values Parameter supply voltage voltage on any other pin operating temperature storage temperature solder point temperature maximum junction temperature Rev. 01 — 8 September 2005 PCA9510A 2 Hot swappable I C-bus and SMBus bus buffer V CC_LOW SDAOUT ...

Page 12

... ENABLE V or GND CC SDA, SCL floating; input only ENABLE ENABLE GND GND mA ENABLE CC Rev. 01 — 8 September 2005 PCA9510A 2 C-bus and SMBus bus buffer Min Typ Max [1] 2.7 - 5.5 [ [1] 0.8 1.1 1.2 - 0.5 V 0.7 CC 0.3 V 0.5 V ...

Page 13

... 100 pF each side SDAn, SCLn pins mA 2.7 V sink CC SDAn, SCLn pins 5 Section 11.1 “Typical performance Rev. 01 — 8 September 2005 PCA9510A 2 C-bus and SMBus bus buffer Min Typ Max [1] [5] 0 110 175 [ [ ...

Page 14

... V 2 amb Fig 13. Input/output t 350 (mV) 250 150 3 Rev. 01 — 8 September 2005 PCA9510A 2 Hot swappable I C-bus and SMBus bus buffer 5 2 +25 T amb > 100 pF PU(in) PU(out) versus temperature ...

Page 15

... Product data sheet idle(READY) , and t dis t en delay idle(READY) delay en and t en idle(READY) Rev. 01 — 8 September 2005 PCA9510A 2 Hot swappable I C-bus and SMBus bus buffer t dis t stp(READY stp(READY) © Koninklijke Philips Electronics N.V. 2005. All rights reserved. 002aab592 002aab593 002aab594 ...

Page 16

... Fig 18. Test circuitry for switching times PCA9510A_1 Product data sheet Hot swappable PULSE D.U.T. GENERATOR the pulse generator o Rev. 01 — 8 September 2005 PCA9510A 2 C-bus and SMBus bus buffer 100 pF 002aab595 © Koninklijke Philips Electronics N.V. 2005. All rights reserved ...

Page 17

... 0.49 0.25 5.0 4.0 1.27 0.36 0.19 4.8 3.8 0.019 0.0100 0.20 0.16 0.244 0.05 0.014 0.0075 0.19 0.15 0.228 REFERENCES JEDEC JEITA MS-012 Rev. 01 — 8 September 2005 PCA9510A 2 Hot swappable I C-bus and SMBus bus buffer detail 6.2 1.0 0.7 1.05 ...

Page 18

... 2.5 scale (1) ( 0.45 0.28 3.1 3.1 0.65 0.25 0.15 2.9 2.9 REFERENCES JEDEC JEITA Rev. 01 — 8 September 2005 PCA9510A 2 Hot swappable I C-bus and SMBus bus buffer detail 5.1 0.7 0.94 0.1 0.1 0.1 4.7 0.4 EUROPEAN PROJECTION © Koninklijke Philips Electronics N.V. 2005. All rights reserved. ...

Page 19

... PCA9510A_1 Product data sheet Hot swappable I 2 called small/thin packages. Rev. 01 — 8 September 2005 PCA9510A 2 C-bus and SMBus bus buffer 3 350 mm so called © Koninklijke Philips Electronics N.V. 2005. All rights reserved ...

Page 20

... LBGA, LFBGA, SQFP, [3] , TFBGA, VFBGA, XSON , SO, SOJ [8] [9] [8] , PMFP , WQCCN.. measured in the atmosphere of the reflow oven. The package Rev. 01 — 8 September 2005 PCA9510A 2 Hot swappable I C-bus and SMBus bus buffer Soldering method Wave not suitable [4] not suitable suitable [5] [6] not recommended ...

Page 21

... Peripheral Component Interface PCI Industrial Computer Manufacturers Group System Management Bus VERSAModule Eurocard Data sheet status Change notice Product data sheet - Rev. 01 — 8 September 2005 PCA9510A 2 C-bus and SMBus bus buffer Doc. number Supersedes - - © Koninklijke Philips Electronics N.V. 2005. All rights reserved ...

Page 22

... Notice — All referenced brands, product names, service names and trademarks are the property of their respective owners C-bus — wordmark and logo are trademarks of Koninklijke Philips Electronics N.V. Rev. 01 — 8 September 2005 PCA9510A 2 C-bus and SMBus bus buffer © Koninklijke Philips Electronics N.V. 2005. All rights reserved ...

Page 23

... No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Published in The Netherlands PCA9510A Date of release: 8 September 2005 Document number: PCA9510A_1 ...

Related keywords