fin210ac Fairchild Semiconductor, fin210ac Datasheet - Page 3

• Manufacturer Part Number: fin210ac
• Description: ?serdes Fin210ac 10-bit Serializer / Deserializer Supporting Cameras And Small Displays Up To 48mhz
• Manufacturer: Fairchild Semiconductor

FIN210AC (Deserializer DIRI=0) Pin Descriptions
Note:
2.
FIN210AC (Deserializer DIRI=0) Pin Configurations
© 2009 Fairchild Semiconductor Corporation
FIN210AC • Rev. 1.0.1
DIRI
XTERM
S0
S1
PWS0
PWS1
/ENZ
DP[1:10]
CKP
DSI+
DSI-
CKSI+
CKSI-
CKSO+
CKSO-
CKREF
STROBE
/DIRO
VDDP
VDDS
VDDA
GND
N/C
Pin Name
G
A
B
C
D
E
F
0=GND; 1=VDDP
42-Ball BGA, 3.5 x 4.5mm, .5mm pitch (Top View)
DP[10]
DP[4]
DP[6]
DP[8]
CKP
N/C
N/C
1
DP[2]
DP[5]
DP[7]
DP[9]
N/C
Control to determine serializer or deserializer configuration.
Control to determine if using internal or external termination
Signals used to define the edge rate of parallel I/O.
Signals used to define the edge rate of parallel I/O.
Configure CKP pulse width.
Configure CKP pulse width.
High-Z or known state outputs during power down
LV-CMOS parallel data output. (N/C if not used)
LV-CMOS word clock output or Pixel clock output.
CTL Differential serial input data signals.
DSI+: Positive signal; DSI-: Negative signal.
CTL Differential deserializer input bit clock.
CKSI+: Positive signal; CKSI-: Negative signal.
CTL Differential serializer output bit clock.
CKSO+: Positive signal; CKSO-: Negative signal.
LV-CMOS clock input and PLL reference.
LV-CMOS strobe input for latching data into the serializer.
LV-CMOS Output. Inversion of DIRI in normal operation.
Power supply for parallel I/O. (All VDDP pins must be connected to VDDP)
Power supply for serial I/O.
Power supply for core.
All GND pins must be connected to ground. BGA: all GND pads. MLP: Pin 28, 29, GND PAD must be grounded.
No connect. BGA: G1, F2; MLP: 10, 11; (Do not connect to GND or VDD)
N/C
N/C
2
XTRM
PWS1
VDDP
Figure 3. FIN210AC (Deserializer DIRI=0) Pin Assignments (Top View)
DP[1]
DP[3]
GND
N/C
3
VDDS
VDDA
PWS0
/ENZ
GND
N/C
N/C
4
STROBE
CKSO+
CKSI+
DSI+
N/C
N/C
S1
5
CKREF
CKSO-
/DIRO
CKSI-
DSI-
DIRI
S0
6
3
VDDP
DP[4]
DP[5] 2
DP[6]
DP[7] 6
DP[8] 7
DP[9] 8
CKP 5
Description
32-pin MLP, 5mm x 5mm, .5mm pitch (Top View)
1
3
4
(Center pad must be grounded)
0 Deserializer
1 Serializer
0 Internal termination used
1 External termination required on CKSI & DSI
No connect unless in “clock pass-through” mode.
No connect unless in “clock pass-through” mode.
No connect unless in “clock pass-through” mode.
No connect if not used.
See Table 2 Deserializer (DIRI=0) Control Pin.
See Table 2 Deserializer (DIRI=0) Control Pin.
See Table 5 Deserializer (DIRI=0) Control Pin.
See Table 2 Deserializer (DIRI=0) Control Pin.
See Table 2 Deserializer (DIRI=0) Control Pin.
DESERIALIZER
GND PAD
www.fairchildsemi.com
24
23
22
21
20
19
18
17
CKSO+
CKSO-
DSI-
DSI+
CKSI-
CKSI+
DIRI
VDDS