at93c46w-10su-2.7 ATMEL Corporation, at93c46w-10su-2.7 Datasheet
at93c46w-10su-2.7
Related parts for at93c46w-10su-2.7
at93c46w-10su-2.7 Summary of contents
Page 1
... Description The AT93C46 provides 1024 bits of serial electrically erasable programmable read- only memory (EEPROM), organized as 64 words of 16 bits each (when the ORG pin is connected to VCC), and 128 words of 8 bits each (when the ORG pin is tied to ground). The device is optimized for use in many industrial and commercial applica- tions where low-power and low-voltage operations are essential ...
Page 2
Absolute Maximum Ratings* Operating Temperature......................................−55°C to +125°C Storage Temperature .........................................−65°C to +150°C Voltage on Any Pin with Respect to Ground ........................................ −1.0V to +7.0V Maximum Operating Voltage .......................................... 6.25V DC Output Current........................................................ 5.0 mA AT93C46 2 *NOTICE: Figure 1. Block ...
Page 3
Table 2. Pin Capacitance Applicable over recommended operating range from T Symbol Test Conditions C Output Capacitance (DO) OUT C Input Capacitance (CS, SK, DI) IN Note: 1. This parameter is characterized and is not 100% tested. Table 3. ...
Page 4
Table 4. AC Characteristics Applicable over recommended operating range from TTL Gate and 100 pF (unless otherwise noted) Symbol Parameter SK Clock f SK Frequency t SK High Time SKH t SK Low Time SKL Minimum ...
Page 5
... Erase instruction and address are decoded. The DO pin outputs the Ready/Busy status of the part brought high after being kept low for a minimum of 250 ns (t logic “1” at pin DO indicates that the selected memory location has been erased and the part is ready for another instruction. ...
Page 6
... The ERAL instruction is valid only WRITE ALL (WRAL): The Write All (WRAL) instruction programs all memory locations with the data patterns specified in the instruction. The DO pin outputs the Ready/Busy status of the part brought high after being kept low for a minimum of 250 ns (t ...
Page 7
Figure 3. READ Timing High Impedance Figure 4. EWEN Timing Figure 5. EWDS Timing 5140B–SEEPR–2/07 ... ... ...
Page 8
Figure 6. WRITE Timing HIGH IMPEDANCE DO (1) Figure 7. WRAL Timing HIGH IMPEDANCE DO Note: 1. Valid only 4.5V to 5.5V. CC Figure 8. ERASE Timing CS SK ...
Page 9
Figure 9. ERAL Timing HIGH IMPEDANCE DO Note: 1. Valid only 4.5V to 5.5V. CC 5140B–SEEPR–2/ STANDBY CHECK STATUS BUSY HIGH IMPEDANCE ...
Page 10
... AT93C46 Ordering Information Ordering Code (2) AT93C46-10PU-2.7 (2) AT93C46-10PU-1.8 (2) AT93C46-10SU-2.7 (2) AT93C46-10SU-1.8 (2) AT93C46W-10SU-2.7 (2) AT93C46W-10SU-1.8 (2) AT93C46-10TU-2.7 (2) AT93C46-10TU-1.8 (2) AT93C46Y1-10YU-1.8 (Not recommended for new designs) (3) AT93C46Y6-10YH-1.8 (2) AT93C46U3-10UU-1.8 (4) AT93C46-W1.8-11 Notes: 1. For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the Table 3 on page 3 and Table 4 on page 4. Not recommended for new design. Please refer to AT93C46D datasheet. ...
Page 11
Packaging Information 8P3 – PDIP Top View PLCS Side View Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information. 2. Dimensions A and L are measured ...
Page 12
JEDEC SOIC Top View e Side View Note: These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 R ...
Page 13
EIAJ SOIC 1 N Top View e D Side View Notes: 1. This drawing is for general information only; refer to EIAJ Drawing EDR-7320 for additional information. 2. Mismatch of the upper and lower dies and resin burrs ...
Page 14
TSSOP Pin 1 indicator this corner N Top View Side View Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, ...
Page 15
PIN 1 BALL PAD CORNER Top View PIN 1 BALL PAD CORNER 1 2 (d1 (e1) Bottom View 8 SOLDER BALLS 1. Dimension “b” is measured at the maximum solder ball diameter. This ...
Page 16
Mini-MAP D Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-229, for proper dimensions, tolerances, datums, etc. 2. Dimension b applies to metallized terminal and is measured between 0.15 mm and 0.30 mm ...
Page 17
Revision History 5140B–SEEPR–2/07 Doc. Rev. Date Comments 5140B 2/2007 Implemented revision history. Added note to page 1 and ordering information; ‘Not recommended for new design; please refer to AT93C46D datasheet’. 17 ...
Page 18
... Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life © 2007 Atmel Corporation. All rights reserved. Atmel trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Atmel Operations Memory ...