X9110_08 INTERSIL [Intersil Corporation], X9110_08 Datasheet
X9110_08
Related parts for X9110_08
X9110_08 Summary of contents
Page 1
Data Sheet Single Digitally-Controlled (XDCP™) Potentiometer The X9110 integrates a single digitally controlled potentiometer (XDCP monolithic CMOS integrated circuit. The digital controlled potentiometer is implemented using 1023 resistive elements in a series array. Between each element are ...
Page 2
Ordering Information PART NUMBER PART MARKING X9110TV14 X9110TV X9110TV14Z* (Note) X9110TV Z X9110TV14I X9110TV I X9110TV14IZ (Note) X9110TV Z I X9110TV14-2.7 X9110TV F X9110TV14Z-2.7 (Note) X9110TV Z F X9110TV14I-2.7 X9110TV G X9110TV14IZ-2.7* (Note) X9110TV Z G *Please refer to TB347 ...
Page 3
Circuit Level Applications • Vary the gain of a voltage amplifier • Provide programmable dc reference voltages for comparators and detectors • Control the volume in audio circuits • Trim out the offset voltage error in a voltage amplifier circuit ...
Page 4
SERIAL DATA PATH FROM INTERFACE CIRCUITRY REGISTER 0 (DR0) REGISTER 2 (DR2) If WCR = 000[HEX] then WCR = 3FF[HEX] then FIGURE 1. DETAILED POTENTIOMETER BLOCK DIAGRAM Potentiometer Pins ...
Page 5
Data Registers via the XFR Data Register; ( loaded with the contents of its data register zero (DR0) upon power-up. The Wiper Counter Register is ...
Page 6
TABLE 4. IDENTIFICATION BYTE FORMAT DEVICE TYPE IDENTIFIER ID3 ID2 0 1 (MSB) TABLE 5. INSTRUCTION BYTE FORMAT INSTRUCTION OPCODE I2 I1 (MSB) Device Instructions Identification Byte (ID and A) The first byte sent to the X9110 from the host, ...
Page 7
Write in Process (WIP bit) The contents of the Data Registers are saved to nonvolatile memory when the CS pin goes from LOW to HIGH after a complete write sequence is received by the device. The progress of this internal ...
Page 8
INSTRUCTION R/W Read Wiper Counter 1 Register Write Wiper Counter 0 Register Read Data Register 1 Write Data Register 0 XFR Data Register to 1 Wiper Counter Register XFR Wiper Counter 0 Register to Data Register Read Status (WIP bit) ...
Page 9
Write Data Register (DR) Device Type Device Instruction Identifier Addresses Opcode CS Falling Edge Transfer Data Register (DR) to ...
Page 10
Absolute Maximum Ratings Voltage on SCK any Address Input with Respect ...
Page 11
D.C. Operating Specifications Over the recommended operating conditions unless otherwise specified SYMBOL PARAMETER I V Supply Current CC1 CC (active Supply Current CC2 CC (nonvolatile write Current (standby Input Leakage Current LI I ...
Page 12
Equivalent A.C. Load Circuit 5V 1462Ω SO pin 2714Ω 100pF AC Timing SYMBOL f SSI/SPI Clock Frequency SCK t SSI/SPI Clock Cycle Time CYC t SSI/SPI Clock High Time WH t SSI/SPI Clock Low Time WL t Lead Time LEAD ...
Page 13
High-Voltage Write Cycle Timing SYMBOL t High-Voltage Write Cycle Time (store instructions) WR XDCP Timing SYMBOL t Wiper Response Time After the Third (last) Power Supply is Stable WRPO t Wiper Response Time After Instruction Issued (all load instructions) WRL ...
Page 14
Timing Diagrams Input Timing CS t LEAD SCK MSB SI HIGH IMPEDANCE SO Output Timing CS SCK t V MSB SO ADDR SI Hold Timing CS SCK HOLD 14 X9110 t CYC ...
Page 15
XDCP Timing (For All Load Instructions) CS SCK MSB HIGH IMPEDANCE SO Write Protect And Device Address Pins Timing Applications information Basic Configurations Of Electronic Potentiometers V R Three terminal Potentiometer; Variable voltage ...
Page 16
Application Circuits NONINVERTING AMPLIFIER – (1 OFFSET VOLTAGE ADJUSTMENT 100kΩ – + TL072 10kΩ 10kΩ 10kΩ +12V -12V 16 X9110 V V ...
Page 17
Application Circuits (continued) ATTENUATOR – -1/2 ≤ G ≤ +1/2 INVERTING AMPLIFIER ...
Page 18
Thin Shrink Small Outline Plastic Packages (TSSOP) N INDEX 0.25(0.010) E AREA E1 - 0.05(0.002) SEATING PLANE - -C- α 0.10(0.004) 0.10(0.004 NOTES: 1. These package ...